REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Kia Sephia / Shuma (1995 release)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Kia
	Sephia / Shuma
		Maintenance
		Engine
		Greasing system
		Cooling
		The power supply system and release
		Fuel system
		Ignition system
		Coupling
		Manual transmission
		Automatic Transmission
		Axes and power shafts
		Steering
		Wheels and tires
		Brakes
		Suspension
		Body
			Technical data
			Front bumper
			Rear bumper
			The front door
			Conformal door seal
			Door hinges and door lock strike plate
			Door lock
			Inner Door handle
			The outer door handle
			Cylinder door lock
			Window switches
			Power windows
			Glass doors
			Backdoor
			Spotlight
			High level brake light
			The rear combination lamp
			Ceiling
			Hood
			Sound signal
			Device combination
			Repair of the instrument cluster
			Replacing bulbs dash
			Printed circuit board
			The top decorative overlay of the panel of devices
			Switches
			The central panel
			Cover center console
			The center console
			Dimmer dashboard
			The left and right lattices of a heater of a windscreen
			The left and right lateral lattices of a heater
			Ducts heating and ventilation systems
			Floor ducts
			Glovebox
			A cable of opening the bonnet
			Handle opening the bonnet
			Dashboard
			The control panel heating and ventilation
			Door mirror
			Replacing the glass door mirror
			The front seats
			Upholstery front seatback
			The upholstery of the front seat
			The leaning back hinge of a forward seat
			Rear seat
			Seat belts
			Lock the front seat
			Front shoulder belt
			Rear seat belts
			Bracket rear seat belt
			Shoulder rear seat belt
			The top furnish of a forward rack
			The bottom furnish of the central rack
			The top furnish of the central rack
			Finish the back of the rack
			Finishing stand legs
			Front side door trim
			Rear door trim
			The trunk lid
			The hinge lid
			Windshield washer hose
			Engine windshield washer
			Wiper Arm
			Sprayers
			Replacing the wiper blades
			Traction wiper
			Wiper Motor
			Distances between body points
		The air conditioning system
		Electrical equipment

printable version

Dashboard

1 - strip the center console;
2 - the center console;
3 - side cover;
4 - lower trim panel;
5 - the top decorative overlay of the panel of devices;
6 - a combination of devices;

7 - control panel heating and ventilation;
8 - the radio;
9 - the glovebox;
10 - central panel finishes;
11 - set of dashboard switches and control devices

Withdrawal

PERFORMANCE ORDER

1. Remove the central console.
2. Remove the driver airbag.
3. Remove the steering wheel, turn signal switch, and the upper and lower casings of a steering column.
4. Remove the nut and release the cable sheath opening the bonnet from the plate on the left side of the instrument panel.
5. Remove the handle of opening the bonnet. Remove the three screws and remove the trim panel on the left side of the instrument panel.
6. Remove the two screws on the left side of the T-shaped connector.
	7. Remove the two screws on the left side of the instrument panel as shown in the figure.
8. Remove the ashtray.
9. Remove the cover of the central console.
10. Remove the control panel heating and ventilation.
11. Remove the glovebox.
12. Remove the center trim panel.
13. Remove the front passenger airbag.
14. Remove the two screws on the right side of the T-shaped connector.
	15. Remove the two screws on the right side of the instrument panel as shown in the figure.
16. Remove the two screws on either side of the steering column, that hold the steering column and instrument panel. Lower the steering column down.
17. Unplug all the connectors that connect the instrument panel and the wiring harness of the car.
18. Remove the instrument panel.

Setting

PERFORMANCE ORDER

1. Install the instrument panel in the car. Make sure the steering wheel is correctly installed through a T-shaped rod with wiring harness before installing the instrument panel. Otherwise, the steering column may not be properly installed.
2. Connect the wiring harness connector and the instrument panel.
3. Replace the two screws on either side of the steering column, that hold the steering column and instrument panel. Torque: 18-26 N ??? m
4. Replace the three screws on the right side of the instrument panel. Torque: 18-26 N ??? m
5. Replace the two screws on the right side of the T-shaped connector. Torque: 18-26 N ??? m
6. Fit the front passenger airbag. Torque: 18-26 N ??? m
7. Set the center trim panel.
8. Install the glove box.
9. Install control panel heating and ventilation.
10. Install the trim center console.
11. Install the ashtray.
12. Replace the two screws on the left side of the instrument panel. Torque: 18-26 N ??? m
13. Replace the two screws on the left side of the T-shaped connector. Torque: 18-26 N ??? m
14. Install the bottom panel trim on the left side of the instrument panel.
15. Install the T-connector and secure with two bolts.
16. fix the nut cover of a cable of opening the bonnet to the dashboard.
17. Set the handle of opening the bonnet.
18. Establish a steering wheel, turn signal switch, and the upper and lower casings of a steering column.
19. Install the driver airbag.
20. Install the central console.
21. Connect the cable to the negative terminal of the battery.

« previos page
Handle opening the bonnet

next page »
The control panel heating and ventilation