| Bore | 82 mm |
| The piston stroke | 90 mm |
| Volume | 2.0 liters |
| Pressure cylinder compression: |
| - Nominal | 171 psi |
| - Minimum | 119 psi |
| The maximum allowable pressure difference between the cylinders | 15 psi |
| The oil pressure (engine warmed up) at 3000 rev / min | 57 - 71 psi |
| Cylinder head |
| The maximum allowable strain | 0.05 mm |
| Valves and valve springs |
| The width of the rim of the valve: |
| - Intake | 1.08 mm |
| - Exhaust | 1.18 mm |
| The diameter of the valve stem: |
| - Intake | 5,875 - 5,890 mm |
| - Exhaust | 5,870 - 5,885 mm |
| The gap between the valve stem and guide bushing: |
| - Intake | 0.025 - 0.060 mm |
| - Exhaust | 0.075 - 0.162 mm |
| Valve spring: |
| - The maximum deviation from a right angle | 1.5 mm |
| - The length in the free state | 36 - 43 mm |
| Camshafts and valve lifters |
| The height of the cam shaft: |
| - Intake | 42.30 mm |
| - Exhaust | 42.66 mm |
| The maximum permissible wear | 0.15 mm |
| The diameter of the bearing journal | 25.53 - 25.56 mm |
| Maximum roundness | 0.003 mm |
| Heartbeat | 0.03 mm |
| Grease the bearing clearance: |
| - nominal | 0.035 - 0.080 mm |
| - The maximum permissible | 0.15 mm |
| Free wheeling | 0.077 - 0.197 mm |
| The diameter of the pusher | 29.48 - 29.50 mm |
| The gap between the plunger and the wall of its housing: |
| - nominal | 0.025 - 0.065 mm |
| - The maximum permissible | 0.178 mm |
| Valve clearance (models 1998) | 0.225 - 0.290 mm |
| The crankshaft and connecting rods |
| Bearing rod: |
| - diameter | 47.185 - 47.200 mm |
| - Maximum taper | 0.005 mm |
| - Maximum roundness | 0.003 mm |
| - The lubricating gap (nominal) | 0.013 - 0.38 mm |
| Backlash (free lift) of a rod: |
| - nominal | 0.108 - 0.258 mm |
| - The maximum permissible | 0.30 mm |
| Main bearing: |
| - diameter | 50.55 - 50.73 mm |
| - Maximum taper | 0.005 mm |
| - Maximum roundness | 0.003 mm |
| - Maximum wear | 0.03 mm |
| Lubricating gap (nominal): |
| - Bearing N3 (central) | 0.030 - 0.055 mm |
| - Other bearings | 0.023 - 0.050 mm |
| - The maximum permissible | 0.065 mm |
| Free wheeling of the crankshaft: |
| - nominal | 0.078 - 0.278 mm |
| - The maximum permissible | 0.295 mm |
| Cylinder block |
| Maximum permissible deformation of the surface of the cylinder | 0.05 mm |
| Bore: |
| - nominal | 81.69 - 81.71 mm |
| - The maximum allowable taper and roundness of the cylinder | 0.01 mm |
| Pistons, piston rings |
| Bore | 81.64 - 81.66 mm |
| The clearance between the piston and the cylinder: |
| - nominal | 0.038 - 0.050 mm |
| - maximum | 0.15 mm |
| Limit the piston ring gap: |
| - Compression Ring: |
??? nominal
| 0.15 - 0.30 mm |
| ??? maximum | 0.50 mm |
| - Scraper ring: |
| ??? nominal | 0.2 - 0.7 mm |
| ??? maximum | 0.875 mm |
| The gap between the piston ring groove and the periphery of the ring (compression ring only): |
| - nominal | 0.035 - 0.065 mm |
| - maximum | 0.083 mm |
