REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Golf II, Jetta (from 1983 to 1992, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Volkswagen
	Golf 2 / Jetta
		General Information
		Engine
		The power supply system
		Coupling
			Specifications
			Transmission type 084
				The mechanism of the clutch
				A rope clutch
				The clutch pedal
				Adjusting Clutch
			Transmission type 020
		Transmission
		Transmission
		Front-wheel Drive
		A steering
		Suspension
		Brakes
		Body
		Electrical

printable version

The mechanism of the clutch

The mechanism of the clutch: a - transmission of type 084; b - transmission of type 085

1 - clutch;

2 - the directing plug;

3 - a bolt;

4 - release bearing;

5 - mounting bracket;

6 - retaining spring;

7 - small sleeve;

8 - shaft clutch lever;

9 - a large bush;

10 - a spring;

11 - a lock ring;

12 - the lever release bearing;

13 - inner sleeve;

14 - outer sleeve;

15 - a sealing ring;

A - the projection;

V - groove

The drive clutch (transmission type 084)

1 - the lever of the clutch;
2 - winding rope clutch;
3 - tip;
4 - toothed washer;
5 - O-ring;
6 - limiter pedal stroke;
7 - a shaft of the clutch pedal;
8 - the plug;
9 - tube clutch pedal;
10 - a lock ring;

11 - the clutch pedal;
12 - cable clutch;
13 - bulkhead;
14 - an arm;
15 - the plug;
16 - the transmission housing;
17 - lock nut;
18 - an adjusting nut;
19 - threaded end of a rope;
20 - spring return

Withdrawal

PERFORMANCE ORDER

1. Remove the gearbox (see. Subsection 5.1).

2. Remove the return spring 20 (see. Fig. Drive clutch (transmission type 084)) with one arm.

3. Turn the lever shaft 8 (see. Fig. The mechanism of the clutch: a - transmission type 084) situated in the clutch housing 1, so that the release bearing 4 has moved up the guide sleeve 2.

4. Remove the two retaining spring 6.

5. Remove the release bearing 4.

6. Remove the brackets 5 of the release bearing 4.

7. Loosen the screws 3 and remove the guide bushing 2.

On models with the transmission type 084

8. Press out a large hub 9.

9. Remove the shaft 8 of the clutch lever.

10. Press out a small bush 7 (if necessary, replacement).

On models with the transmission type 085

A warning

Clutch lever for the transmission of type 085 has a different structure.

11. Remove the retaining ring 11 (see. Fig. The mechanism of the clutch: b - transmission of type 085).

12. Pull the lever shaft 8 from the clutch housing 1 clutch lever at the same time removing the release bearing 12 and a sealing ring 15.

13. Press out the inner 13 and outer sleeve 14 (if necessary, replacement).

Setting

A warning

Do not wash the release bearing, so as not to wash the grease from it.

PERFORMANCE ORDER

1. Installation of the clutch mechanism is carried out in reverse order, with the following.

2. Check the release bearing by rotating it. If the bearing is jammed, noisy or there is a backlash between the rings, then it must be replaced.

3. Check all bushings for wear.

4. Coat the surface of the graphite grease release bearing guide sleeve 4 and 2.

5. Drive in the bushing 7 is flush with the slot in the clutch housing 1.

6. Insert the projection on the sleeve 9 And in the groove on the sleeve in the housing 1 for pressing the clutch sleeve 9.

7. Press in the inner 13 and outer sleeve 14 for the transmission of type 085 is flush with the slots in the clutch housing 1.

« previos page
Transmission type 084

next page »
A rope clutch