 printable version
The accelerator cable
Withdrawal Remove the bottom casing panel of the driver's side. Disconnect the accelerator cable from the top of the accelerator pedal. Remove the rubber seal waterproof housing at the rear of the engine compartment.
| Fig. 3.1.1. The direction of removal of the rubber seal waterproof casing (1)
|
Vehicles with four-cylinder engines
| Fig. 3.1.2. Location screws engine cover
|
Remove the three screws and remove the engine cover (see. Fig. 3.1.2).
| Fig. 4.19. Fixing accelerator cable to the throttle lever drive vehicles with four-cylinder engines: 1 - an arm; 2 - a spring clamp; 3 - a shell accelerator cable; 4 - grommet accelerator cable sheath; 5 - the accelerator cable end
|
Disconnect the cable end 5 accelerator from the lever throttle actuator (Fig. 4.19). Remove the cover of a cable of an accelerator 3 (see. Fig. 4.19) of a rubber sleeve 4 bracket 1.
Vehicles with six-cylinder engines
| Fig. 4.20. Location vacuum hose (2) and bolts (1) securing the vacuum chamber cruise control
|
On vehicles with cruise control, disconnect the vacuum hose from the vacuum chamber 2 cruise control system (Fig. 4.20). Turn out two bolts and remove an arm of the vacuum chamber of the cruise control.
| Fig. 4.21. The elements of the fuel system six-cylinder engine 1 - the air filter; 2 - bolt 20 Nm; 3 - air mass meter G70; 4 - an electric socket coolant temperature sensor G62; 5 - coolant temperature sensor G62; 6 - a sealing ring; 7 - a hose of return of fuel; 8 - the fuel hose; 9 - a bolt 10 Nm; 10 - a spring clamp; 11 - Air connection; 12 - engine control unit Motronic J220; 13 - the pressure plate; 14 - 28-pin electrical connector; 15 - an electric socket; 16 - air intake elbow; 17 - 2-pin electrical connector (black) temperature sensor to the engine air G42; 18 - bolt 10 Nm; 19 - 2-pin electrical connector overpressure valve in the intake manifold N156; 20 - valve crankcase breather; 21 - seal; 22 - 4-pin electrical connector for lambda probe and lambda probe heater; 23 - 2-pin electrical connector (black) nozzles N30, N31, N32, N33, N83, N84; 24 - Lambda probe G108, 50 Nm; 25 - bolt 10 Nm; 26 - the engine speed sensor G28; 27 - a sealing ring; 28 - a lining; 29 - 2-pin electrical connector (gray) engine speed sensor; 30 - the vacuum chamber; 31 - a lining; 32 - the inlet manifold; 33 - the fuel line to the injectors; 34 - Lambda probe G39, 50 Nm
|
| Fig. 4.22. Fixing accelerator cable to the throttle lever drive vehicles with six-cylinder engines: 1 - a tip of a cable of an accelerator; 2 - an arm; 3 - a spring clip; 4 - grommet accelerator cable sheath; 5 - a spring clamp
|
Using open-end wrench 8 mm, remove the tip of a cable of an accelerator from the lever 1 the throttle (Fig. 4.22). Remove the spring clip mounting shell 3 accelerator cable to the bracket 2, and remove the cable from the bracket 2. Using the screwdriver blade as a lever, remove the spring retainer 5.
Cars with automatic transmission
| Fig. 4.23. Location electrical connector (2) switch of compulsory inclusion of low transmission (kick-down) and clips (1) securing the accelerator cable
|
Unplug electrical connector 2 switches compulsory inclusion of low transmission (kick-down) (Fig. 4.23).
All models Release the clamp 1 (see. Fig. 4.23) fixing accelerator cable.
| Fig. 4.24. The direction of rotation (1) and remove (2) the accelerator cable from the bulkhead
|
Turn the lock on the accelerator cable 90 ?� counterclockwise 1 (Fig. 4.24) and remove it from the bulkhead panel and the plenum.
Setting Installation is spent to sequences, return to removal, taking into account the following. Avoid kinking the accelerator cable.
Vehicles with manual transmission On the side of the engine compartment miss accelerator cable through a hole in the bulkhead panel and the plenum and secure it with a clamp 1 (see. Fig. 4.23).
Cars with automatic transmission From the plenum miss accelerator cable through a hole in the bulkhead panel and the plenum and secure it with a clamp 1 (see. Fig. 4.23). Connect the electrical connector 2 switches compulsory inclusion of low transmission (kick-down) (see. Fig. 4.23).
All models After installing the cable lock accelerator bulkhead turn it 90 ?� clockwise (Fig. 4.24). Adjust the accelerator cable.
Adjustment To adjust the position of the accelerator cable needed help of a second mechanic.
Vehicles with four-cylinder engines Disconnect the cable end 5 (see. Fig. 4.19) accelerator from the lever throttle actuator. Remove the spring retainer 2 (see. Fig. 4.19) sheath accelerator 3.
Vehicles with six-cylinder engines Remove the spring clip 3 (see. Fig. 4.22) and the rubber plug 4 with the shell of the accelerator cable bracket.
All models Press the accelerator pedal all the way and adjust the position of the accelerator cable so that the throttle was fully open. The position of the accelerator cable is adjusted by moving the rubber plug on the cable sheath. In this position, insert the grommet cover and secure it with the spring clip. On cars with automatic gearbox when the accelerator cable adjustment throttle must be fully opened and the switch of compulsory inclusion of low transmission (kick-down) must be turned on (you should hear a click). After adjusting the throttle cable Check the throttle position at idle.
| 
