 printable version
Fuel tank
Withdrawal
A WARNING Even in an empty fuel tank has a pair of fuel, so be careful. |
| Fig. 4.3. Front-wheel drive Fuel Tank: 1 - supply pipe fuel vapor to the absorber; 2 - the fuel return pipe; 3 - the fuel supply pipe to the fuel filter; 4 - bolt M8h35 23 Nm; 5 - overflow hose; 6 - rubber sleeve; 7 - a lock ring; 8 - filler cap; 9 - a sealing ring; 10 - a sealing ring; 11 - bypass valve (upright - is opened, when tilting to 45 ?� - is closed); 12 - non-return valve; 13 - a sealing ring; 14 - exhaust valve; 15 - wire connection with "weight"; 16 - vent pipe; 17 - the fuel tank; 18 - tape for fixing the fuel tank; 19 - a bolt, M8h28, 23 Nm
|
The fuel tank 17 (Fig. 4.3) is removed from the bottom of the car. To support the fuel tank using a jack. Before disconnecting the battery, check whether you have the code switch on the radio. Switch off the ignition and disconnect a wire of "weight" from the storage battery. Briefly open and close the cover toplivonalivnoy neck. Drain the fuel from the fuel tank. Front-wheel drive cars Remove the cover, located under the luggage compartment carpet.
| Fig. 4.15. Disconnecting the electrical connector and the location of supply tubes (1) and return (2) of fuel at the fuel pump
|
Disconnect the 4-pin electrical connector (see. Fig. 4.15). Remove protection arch rear right wheel. Clean the area around the top of the toplivonalivnoy neck. Remove the cover and acting as a lever blade screwdriver, remove the rubber sleeve from the top of toplivonalivnoy neck. From under the arches of the rear right wheel, remove the bolt toplivonalivnoy top of the neck.
| Fig. 4.4. Location screws protective panel
|
Remove the access panel located in front of the rear axle (Fig. 4.4).
Vehicles with self-leveling suspension
| Fig. 4.5. Location sensor bolt mounting height suspension G84
|
Remove the sensor mounting bolt mounting height G84 suspension to the body (Fig. 4.5).
All models
| Fig. 4.6. Location fuel hose (1) the fuel return (2) and the ventilation (3)
|
Disconnect the fuel supply hose 1 (Fig. 4.6) from the fuel filter.
A WARNING The fuel system is pressurized. Before releasing elements of the fuel system to relieve pressure in the system. To do this, close the connection point of the fuel system and a clean cloth, being careful, gently loosen the union nut. |
Sign the fuel return pipe 2 and a ventilation hose 3 and disconnect them.
| Fig. 4.9. Designated connecting wire of "weight"
|
Cars with an additional heater Disconnect the fuel hose to the additional heater.
All models Place the jack under the fuel tank to the base plate and lift the jack so that the weight of the fuel tank perceived jack.
| Fig. 4.7. Location tapes bolts of the fuel tank
|
Note the location of the tape fastening the fuel tank, remove the bolts 1-6 (Fig. 4.7) and remove the tape. With assistant lower the fuel tank, thus, be careful not to bend the fuel tubes.
Setting Installation is spent to sequences, return to removal, taking into account the following. Make sure that the hoses are connected properly and securely attached with clamps. When you install all the O-rings replaced.
| Fig. 4.8. Attaching the fuel hose, fuel return and tank vent on the front right side of the fuel tank
|
Make sure that the fuel hoses, fuel return and ventilation tank mounted on the front right side of the fuel tank (Fig. 4.8). Make sure that the wire is connected to "weight" is connected to the ring on the neck toplivonalivnoy. Under the arch rear right wheel screw bolt of the upper part of the neck with toplivonalivnoy "mass" contact.
A WARNING Once installed, using an ohmmeter, check the resistance between the "weight" on toplivonalivnoy neck ring and the metal part of the body, which should be close to 0. |
After fastening the tapes securing the fuel tank put on the bolt protruding protective caps to protect the spare tire from damage. Connect a wire of "weight" to the battery. Fit the rear right wheel arch. Turn on the radio and enter the code. Lift up the power window glass until it stops. Then click on all window switches again for at least 1, in the closed position of the control unit to activate windows. Set the clock. Before starting the engine, check the availability and level of oil in the engine. After separation of the various electrical connections in the memory control unit writes error information to be erased after installation. Start up the engine and check the tightness of supply.
| 
