Job stereo receiver (H280) (optional)

Power switch.

Radio with cassette works when the ignition key is in the ?�ON?� (?�On.") Or "ACC (" Options "). Click on the button to turn on the power. In receive mode, the radio station on the LCD display shows the frequency of the station, during playback of tapes - an indicator of the direction of the belt, and during playback of CD - recording indicator ("tracks"). to turn off the Radio with cassette, press the button again.

Volume knob.

To increase the volume, turn the knob clockwise, and to decrease the volume - turn it counterclockwise.

BASS / BALANCE (Tone knob in the low sound frequencies / knob left / right stereo balance).

BASS (adjustment knob tone in the low audio frequencies).

Click on the handle so that it popped out. To increase the tone in the low-frequency sound, turn the knob clockwise to decrease the tone in the low-frequency sound - rotate the knob counterclockwise.

BALANCE (knob left / right stereo balance).

Pull the handle is pulled out at the next fixed position. Turn the knob clockwise to increase the volume of the right speaker (left speaker volume decreases). By turning the knob clockwise increases the volume of the left speaker (right speaker volume decreases).

TREBLE / FAD Knob (knob tone in the treble / knob front / rear audio balance).

TREBLE Control Knob (knob tone in the treble).

Click on the handle to eject it out and turn it left or right to set the desired tone in the treble.

FAD (Fader Control) Knob (knob front / rear audio balance).

Pull the handle is pulled out at the next fixed position. Turn the knob clockwise to increase the volume of the front speakers (the volume of the rear speakers is reduced). By turning the knob clockwise increases the volume of the rear speakers (front speaker volume decreases).

TUNE (the manual infusion rate).

Click on the side or this button to increase or decrease the frequency. To continue the search, press and hold one side of the button until the desired frequency.

Automatic tuning frequency.

Press and hold the tuning frequency (TUNE) for 0.5 seconds or longer, it is released when the receiver will automatically configure themselves to the next possible station, which is accompanied by an audible signal. By clicking on the side button for 0.5 seconds or longer, and when released Radio with cassette automatically tunes to the next station with a higher frequency of broadcasts, and when you press the side button for 0.5 seconds or longer, and when it is lowered - Radio with cassette automatically tunes to the next station with a lower frequency broadcast.

Buttons storing stations.

You can enter this Radio with cassette memory for 6 stations in each band, AM, FM1 and FM2.

Storing the stations

In Memory of the radio, you can make 6 stations in the AM band and 12 stations in FM. After that, pressing the range selection and one of the six buttons storing stations you can select one of them. to put in the memory of the station, follow these steps:

- Click on the button to select the range in order to select one of the band AM, FM1, or FM2.

- Select the station you wish to store in memory, using manual or automatic tuning;

- Select the memory station that should be assigned to this station;

- Press and hold the button to store the stations for two or more seconds. The display shows the index number of the selected button storing stations. After store the frequency of its value will be flashing. Release the button and continue storing the next desired station.

Total 18 stations can be programmed by setting a button, a station broadcasting in the AM band, and two - in FM.

At the end of programming including any of the preset stations, after selecting one of the band AM, FM1, or FM2, and clicking on the appropriate button memory frequency stations.

FM / AM (range selection button).

When you press this button, the band AM, FM1 and FM2. The selected range is displayed on the LCD.

EQ (button tone correction).

To obtain the desired quality of the sound, press this button to select the mode:

Button memorize stations with the best sound.

If you click on this button and hold it for two seconds or more, it will be automatically stored to 6 stations with the most intense signal. The stations are stored in order, as the frequency increases.

Buttons tape fast forward / rewind.

Fast forward the tape (?�FF?�) is started by pressing a button during playback of the recording (?�PLAY?�) or fast rewind (?�REW?�).

Pressing the button again during fast-forward the tape (?�FF?�) starts playing a recording.

Rewind, (?�REW?�) is started by pressing a button during playback of the recording (?�PLAY?�) or fast-forward the tape (?�FF?�).

Pressing the button again during fast rewind (?�REW?�) starts playing a recording.

The buttons move to the top of the record.

To find the beginning of each song recorded on the tape, press this button. The distance between the recordings should be at least 4 seconds, this function can work.

By clicking on the button will return to the beginning of the next record.

By clicking on the button will return to the beginning of the current recording.

TAPE PROGRAM Button (the button changes the direction of the belt).

Press this button to change the direction of the belt. This indicator appears on the direction of motion of the tape.

EJECT Button (tape eject button).

When you press the button is the extraction of the tape, if it is inside the radio.

When pressed during fast rewind / forward the tape is extracted.

EQ Button (key tone correction).

To obtain the desired quality of the sound, press this button to select the mode:

DOLBY Button (button noise reduction "Dolby").

When playing in the background you hear constant noise, you can suppress it by simply pressing the button.

If you want to disable this feature, press the button again.