printable version
Door
Door upholstery Switch off the ignition and disconnect the wire from the negative battery terminal.
| Fig. 12.7. Front door: 1 - exterior trim; 2 - molding; 3 - the front door; 4 - seal; 5 - sealing glass; 6 - glass; 7 - windows; 8 - arm; 9 - outside door handle; 10 - thrust ring; 11 - ring; 12 - the handle of window; 13 - shock plate; 14 - lock the door; 15 - inner door handle; 16 - door lock cylinder; 17 - interior doors; 18 - Limiter door opening; 19 - pin limiter
|
| Fig. 12.8. Rear door: 1 - molding; 2 - rear door; 3 - seal; 4 - sealing glass; 5 - B-pillar; 6 - seal triangular vents interior; 7 - glass; 8 - triangular pane cabin; 9 - support of the glass; 10 - windows; 11 - thrust ring; 12 - ring; 13 - the handle of window; 14 - shock plate; 15 - lock the door; 16 - inner door handle; 17 - external door handle; 18 - arm; 19 - interior doors; 20 - Limiter door opening; 21 - pin limiter
|
Remove the pen drive window (the window with manual transmission) or a switch (power window) (Fig. 12.7, 12.8). Thrust ring, which fixes window handle is freed, if you put a clean cloth between the handle and the door trim and stretching the fabric opposite ends of the thrust ring, thrust ring hook and release it. It is necessary to pull the stick back to it after the release of the thrust ring removed from the slots window. Uncover the inside door handle. Remove the retaining screws that secure the armrest. Use a screwdriver with a wide blade, disconnect the clamps on the perimeter and separate door trim from the door. Catches are set very tight, so care is needed not to break them during removal. Remove the door trim by removing it from the door lock knobs and moving upwards. Carefully remove the tape that protects the door against water. Installation is spent to sequences, return to removal, taking into account the following. Carefully place the film, which protects the door from hitting the water to its original position, establishing it no creases or tears. Before installation, check and if necessary replace locks that were broken when removing the door trim. When installing door trim upholstery, position the top of the handle of the door lock and press it until it into place. Very pushing the upholstery in the locations of clamps, secure the upholstery on the door. Fasteners Upholstery Plastic joint, resembling self-tapping screw is widely used for mounting various elements of the upholstery. Although this connector acts as a screw, it is really a combination of self-tapping screws and locking. Cutting the base of the connector expands when it is screwed into the screw. To remove the connector, hold the base of his fingers and unscrew the screw with a Phillips screwdriver, and then remove the base of a flat screwdriver. To insert the connector, set the base to the required position with a screwdriver and a screw in the screw.
The outer door handle Raise the glass up to the stop. Remove the door trim and waterproof film.
| Fig. 12.9. Use a flathead screwdriver to disconnect draft from the outside door handle
|
Flat screwdriver disconnect draft from the outside door handle (Fig. 12.9). Remove the bolts and remove the outside door handle. Disconnect the connector from the switch of the door handle (if fitted). Installation is performed in reverse order of removal.
Door mirror On models with electric windows, disconnect the wire from the negative battery terminal.
| Fig. 12.10. Fasteners door mirror: 1 - a decorative overlay; 2 - the screw; 3 - Mirror
|
On models with electric windows, disconnect the electrical connector from the mirror. Remove the screws and remove the mirror. Installation is performed in reverse order of removal. Glass and windows Lower the glass door, remove the door trim and waterproof film. On models with electric windows, disconnect the wire from the negative battery terminal. On the rear doors, remove the tape seal.
| Fig. 12.11. Location bolts to the window glass
|
Move the windows in such a position that bolts to the window glass are available through technological holes in the inner door panel (Fig. 12.11). Remove the bolts. On models with electric windows, disconnect the connector from the power window motor. At the front door, remove the screws and remove the glass.
| Fig. 12.12. Removing the B-pillar to the rear door
|
On the rear doors, remove the screw and bolt, remove the central rack (Fig. 12.12). Hatchback glass down, remove the glass support with a guide and then moving up, remove the glass from the door.
| Fig. 12.13. Removal from the front door window
|
On the front and rear doors, remove the screws and remove the windows through technological holes in the inner door panel (Fig. 12.13). On models with electric windows Remove the bolt and the engine from the window.
A WARNING Be very careful when removing the engine, as it will be released spring stopper window returns to the up position. |
Installation is spent to sequences, return to removal, taking into account the following.
| Fig. 12.14. Set triangular glass panes
|
To facilitate the installation of glass triangular panes of glass framed grease soap solution (Fig. 12.14). On models with electric windows, connect the wire to the negative terminal of the battery before installation and lower the glass windows in the down position. After installation is complete, check the operation window, repeatedly raising and lowering the window to be sure that it moves freely and easily. If necessary, loosen the screws and adjust the position of the window.
Removal, installation and adjustment of the position of the door Withdrawal On models with electric windows, disconnect the wire from the negative battery terminal. Remove the pin wiring harness door. To access the connector may need to first remove the door trim or related body panels.
| Fig. 12.15. Location door hinge bolts
|
Marker, mark the position of the door hinge bolts (Fig. 12.15). Remove the door opening limiter. Open the door and maintain its stand or jack, having laid between them and the door clean cloth. Ask the assistant to support the door. Unscrew the hinges from the door or from the rack and remove the door. Setting Installation is performed in reverse order of removal. Secure pylevlagozaschitnuyu film (if removed), establishing it no creases or tears. The surface on which the film is adhered pylevlagozaschitnaya should be perfectly clean. If the installation is carried out before the door is removed, align before labeling. Adjusting the doors Check the condition of the door hinges, which open the door and lift it up without lifting the body. After installing the door, make sure that the gap around the perimeter of the door was the same everywhere, and the outer surface of the door is flush with the rest of the body. To adjust the gap around the perimeter of the door, loosen the bolts hinges and door to door by moving the door, adjust its position, then tighten the bolts.
| Fig. 12.16. The direction of movement of a shock plate of the door lock to adjust the back of the door
|
At least loosen the screws and adjust the position of a shock plate of the door lock so that the rear part of the door is flush with the back door or the elements of the body (Fig. 12.16).
|