add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Passat B6 (from 2004 year)

general info. full specifications. diagnostics. hints. tips. tricks
Volkswagen Passat B6
Home
 
Volkswagen
Passat B6
Operation and maintenance of car
Engine
Overview
Mechanical parts (engine volume 1.6 liters)
Lubrication system
Cooling System
Fuel Injection System
The mechanical part (petrol engines of 2.0 liters)
Lubrication system
System ohlazhdeiya
Fuel System
Injection System
The exhaust system otrabotavschih gases
Ignition System
The mechanical part (diesel engines of 2.0 liters)
Lubrication system
Cooling System
Check cooling system for leaks
Check the pressure reducing valve in the lid of the surge tank
Check oil cooler for leaks
Drain the coolant and the Bay
Removing and replacing the fan with bracket
Removing and replacing the water pump
Removing and replacing the thermostat
Fuel System
Pressurization system with a turbocharger, operating at OG
The system of direct injection diesel
The exhaust system
Table
Transmission
Chassis
Steering mechanism
Brake System
Onboard electrical
Body
Electrical circuit
 


Hit Counter by Digits


print page printable version

Cooling System







Components of Cooling System
Fig. 2,329 . The components of the cooling system: 1 - radiator, 2 - O-ring, 3 - Coolant hose, upper, 4 - Cap 5 - plug, 6 - bolt to 5 N • m, 7 - expansion tank, 8 - bottom hose of the cooling system 9 - bolt 10 Nm, 10 - Bolt 5 Nm, 11 - an extra cooling fan, 12 - the main cooling fan, 13 - Plug, 14 - Bracket Fan



WARNING
When all construction works, particularly in the engine compartment, due to the dense layout, note the following.

Backbone of all kinds (such as fuel, hydraulic, absorber with activated charcoal, cooling systems, circuit conditioning systems, brake ducts, vacuum hoses), as well as electrical wires must be run as they were built originally.
Provide space for all moving and hot components.

NOTE
With a warm engine cooling system is under pressure. If necessary before repair works to relieve pressure.
Hose fittings secured with spring clamps. When repairing only use spring clamps.
For installation of spring clips is recommended to use pliers for spring clamps or pliers for hose clamps.
When installing the drain hose of the cooling system for pulling them. Make sure they do not touch other components (Observe the marking on the fitting and radiator hose).

Plan for connecting hoses of the cooling system (cars with manual transmission)

Wiring diagram of the cooling system hoses
Fig. 2.330 . Wiring diagram of the cooling system hoses: 1 - expansion tank, 2 - bypass cap, 3 - heater, 4 - heat exchanger heating system, 5 - cylinder head / cylinder block, 6 - upper hose of the cooling system, 7 - heater; 8 - bottom hose cooling system; 9 - engine oil cooler, 10 - water pump / thermostat, 11 - an extra heater


Wiring diagram of the cooling system hoses
Fig. 2,331 . Wiring diagram of the cooling system hoses: 1 - expansion tank, 2 - bypass cap, 3 - heater, 4 - heat exchanger heating system, 5 - transmission oil cooler, 6 - cylinder head / cylinder block, and 7 - the upper hose of the cooling system, 8 - Engine oil cooler 9 - Radiator, 10 - bottom hose of the cooling system, 11 - water pump / thermostat, 12 - the additional heater



Plan to connect the cooling system hoses (vtomobili with gearbox DSG)




« previos page
Check oil pressure and oil pressure sensor
next page »
Check cooling system for leaks

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.