 printable version
Service elements throttle actuator
Lubrication, checking of mobility and condition of the joints of the lever throttle actuator  | Try to avoid getting lubricant on the plastic hinges drive! |
 | The design of the throttle lever |
 | Location of the accelerator pedal position sensor (B37) |
| - The design of the throttle lever shown in the illustration above, if necessary, remove the air cleaner (see. Section Removal and installation of components of an inlet air path).
- Make articulations lubrication of the drive mechanism, Ball assemblage should be divided, fill with grease, and then to articulate again - do not forget about the spherical bearing on the accelerator pedal position sensor (B37).
- Carefully lubricate all bearing surfaces of rods and levers, and exposed hinges and cables.
- Slowly squeeze until it stops, then release the gas pedal - the detection of signs of play or seizure replace the accelerator cable (see. Below).
|
|
Check and adjust the throttle Adjusting the throttle (all models)
| - Check progress freedom and the general condition of the lever (2), the position sensor (TPS) and drive cable (1).
- Run the engine at idle speed, - the lever (2) TPS should pull over to the fence (a) a closed throttle position (accelerator pedal (5) is released). If necessary tweak lever position by turning the adjusting screw (3), taking place entirely by backlash.
- Connect the reader STAR DIAGNOSIS and clean the memory module on-board self-diagnostic system (see chap. Systems of an electric motor).
- Depress the pedal (5) to the stop in the gauge-switch activate the kickdown (4) (do not activate mode), and by means of the adjusting screw (3) until the lever pressed against the fence TPS (b).
- Again, clean the memory module on-board self-diagnostic system (see chap. Systems of an electric motor).
- Visually make progress in the fullness of the throttle valve, lubricate the exposed drive cable corrosion grease (001 989 37 51 10).
|
|
Removing and installing the throttle cable Details of installation of the throttle cable (all models)
| - Disconnect the drive cable (30) from the head of the spherical bearing.
- Press together the plastic clips (30/4) and pull out the fixed arm (10), complete with drive cable (30).
- Remove the cover to the left under the dashboard.
- Push the cable from the engine compartment into the passenger compartment, - try to prevent the loss of the rubber grommet (30/6).
- Rope Pull assembly (30) from the engine compartment.
- Installation is in the reverse order.
- Finally, adjust the actuator (See above.) And lubricate the exposed areas of the rope assembly corrosion grease (001 989 37 51 10).
|
|
Removal and installation of the accelerator pedal position sensor Details of installation of the accelerator pedal stroke sensor (all models)
| - Disconnect the return spring (31/9).
- Raschekante retainer (25/3).
- Pull the lever transmission with built-in remote socket (25/4) - Do not disconnect the accelerator cable
- Disconnect the electrical connector.
- Otboltite accelerator pedal position sensor (R25 / 2) from the fixed lever (25/5).
- Installation is in the reverse order - track correctness of landing lock washer. Check the operation of the drive, if necessary, make the appropriate adjustment (see. Above).
|
|
Removal and installation of the gas pedal and its arm Pedal Details of installation of the gas pedal (all models)
| - Remove the clip (24/3).
- Disconnect the lower end of the gas pedal (1).
- Expand the pedal (1) to the left on the rod (2) so that the sample (3) is pushed onto the cam (4) of the stem (2).
- Remove the pedal filing her back and separated from the stem.
- Installation is in the reverse order.
|
|
Pedal arm Details of installation of the accelerator lever (all models)
| - Remove the cover (1) to the left under the dashboard.
- Remove the pedal assembly (2) (See above.).
- Remove the front section of the carpet in the driver's footswitch well.
- Remove the spring (3).
- Remove the bolts (4) securing the swivel bearing (6) to the engine compartment bulkhead.
- Remove the retaining ring (5).
- Remove the swivel bearing (6) in assembly with the pedal lever (7).
- Remove the locking pin (8) and a separate support (6) from the lever (7).
- Installation is in the reverse order - make sure that the pin (8) was in the receptacle in the engine compartment bulkhead.
|
|
|
