add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Golf III / Vento (from 1991 to 1997, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks
Volkswagen Golf 3 / Vento
Home
 
Volkswagen
Golf 3 / Vento
Operating instructions
eleven The identity of the vehicle
Controls
Device combination
HVAC salon
Operations in the car
Locks
Engine start
Features of operation of various modifications of the family car Golf III
Replacing bulbs
Maintenance
Service Features auto-mobiles Golf III, equipped with a diesel engine
Lifting and towing vehicle
Tool, trailer coupling, spare wheel
Wheels and tires
Gasoline Engine
Diesel engine
Exhaust system
Transmission
The suspension of the car
Steering
The brake system
Electrical
Body
Diagrams
 


Hit Counter by Digits


print page printable version

Replacing bulbs



Information about the lamps used in automobiles Golf III, their characteristics and the amount shown in Table. 12.
Replacement lamps front lens unit. Remove the protective cover from the inside of the lens unit, disconnect the connector, then remove the spring latch. Remove the lamp by holding the contact group. Install the new lamp so that the middle connector pin was located at the top. Installation is the reverse order. Be careful! Avoid contamination of the bulb. If this should happen, carefully clean their lint-free cloth. If you accidentally touch hands, clean the lamp bulb with a cloth moistened with alcohol.
Replacement of lamps of dimensional light in the headlamp. Remove the protective cover unit lights. Remove the optical element holder assembly with the lamp, carefully push the bulb by turning counterclockwise and pull it out of the holder.

Remove the cover dual lens unit. The arrows indicate the latch
Fig. 1.14. Remove the cover dual lens unit. The arrows indicate the latch


Replacing the lamp dual lens unit (options ?�GT?�, ?�GTI?�, ?�GTP?�, ?�GT?� ?�TDI?� have the lens unit with an additional lamp beam). Produced in the same way as the standard lens unit, eliminating the protective cover, which is removed after clicking on the clips (Fig. 1.14) (some cars Golf).

Replacing the lamp fog lamp and installation of decorative overlays
Fig. 1.15. Replacing the lamp fog lamp and installation of decorative overlays: 1 - the connector; 2 - spring latch


Replacing fog lamp bulbs. Hook and remove the trim from the front bumper, unscrew the lamp, remove it from the slot. Then turn the lights casing counterclockwise and remove it. Next, remove the connector 1 (Fig. 1.15) and remove the spring latch from the bulb holder and fold it. Remove the bulb from the holder and insert a new, so that the locking protrusions of the optical element lights included in the recesses cup lamp. Fix the lamp spring latch. Connect the connector lights. Put the headlamp housing and turn it clockwise. Fasten the headlight in the front bumper with the two screws. Insert the trim outside of the bumper into the slot, and then turn the cover, push it until it clicks into the latches.
Replacement lamps front indicators. Remove the front bumper trim (see. Above), press the spring latch and pull out of the nest bumper turn signal housing. Turn the bulb holder anticlockwise and remove it from the housing index. Gently press the bulb, turn it counterclockwise, remove the cartridge. Installation is the reverse order.
Replacing bulbs side direction indicators. Pry the side turn signal. Slightly turning the holder counterclockwise, remove it from the lamp. Replace the bulb. Installation is the reverse order.
Replacement of lamps of a back lantern. Remove the cover of the rear light inside. Next, disconnect the connectors from the back side of the lamp unit and remove it by unscrewing the nut. To replace the bulb, gently press down, rotate counterclockwise and remove the cartridge. If necessary, replace the seal rear light.
Replacing bulbs license plate light. Remove the screws that secure the lens, remove the bulb holder. Installation is the reverse order. During her be careful not to over-tighten the screws that secure the lens, just place the sealing washers.
Replacing the lamp room lamp. Thin knife detach the lens from the body of the ceiling. Replace the bulb, set the lens.
Lamp Replacement lamp for reading. Remove the common housing and ceiling lamp by inserting a screwdriver blade between the base and the roof lining. Remove the bulb holder by turning counterclockwise. Remove the bulb by turning it clockwise until it stops. Put in place a common housing and ceiling lamp, first inserting into the groove of the roof facing the left side of the body.




« previos page
Automatic transmission
next page »
Maintenance

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.