 printable version
Front side door trim
| Fig. 16.29. Front side door trim: 1 - internal transition element; 2 - inner liner; 3 - door lining; 4 - window switch; 5 - tweeter; 6 - an external speaker; 7 - inner door handle; 8 - central locking switch (driver's side only); 9 - trim panel; 10 - an arm pads; 11 - lining; 12 - a lamp signaling the door open; 13 - gasket retainer; 14 - transition element; 15 - an external liner; 16 - directing a button; 17 - a protective film; 18 - foam seal
|
The upholstery of the front door is shown in Fig. 16.29.
Withdrawal Remove the switch window. The driver's door
| Fig. 16.30. Removing the power window switch from the front door trim on the driver: 1 - the switch; 2 - switch lock; 3 - Screwdriver; A - direction of squeezing the lock switch; B - direction of removal of the circuit breaker
|
Insert the edge of a thin screwdriver up to the stop in the hole located under the handle of the door. Clutching the handle of a screwdriver to the door trim, blade screwdriver press the power switch lock and window, pressing the switch up and pull it out of the door trim (Fig. 16.30). The door on the passenger side If a door handle has a hole, the lifting power window switch is made in the same way as on the driver's door.
| Fig. 16.31. Removing the power window switch from the front door trim on the passenger side: 1 - the switch; 2 - switch lock; 3 - Screwdriver; 4 - adhesive tape; A - direction of squeezing the lock switch
|
If the hole under the door handle is missing, tape the handle about a switch blade small screwdriver press the switch and pull it up (Fig. 16.31). Both doors Release the locking protrusion on the switch and unplug the electrical connector.
| Fig. 16.32. Removing door trim: 1 - the front door trim; 2 - screws, 1.5 Nm; 3 - a clip; 4 - Clip; 5 - windows
|
Remove the two screws 2 (Fig. 16.32) fastening the door trim. Pick up approximately 200 mm in the door trim and remove it.
| Fig. 16.33. Tie the rope (3) of the internal handle of opening the door, cable cover (1) and the guide clip (2)
|
Disconnect the cable end of the internal handle of opening of a door lock and a cable cover from the guide clip (Fig. 16.33). On the reverse side of the door trim disconnect electric sockets from the central locking switch, the lamp lights up when you open the door, anti-theft alarm and speakers.
Setting Please check for correct installation of terminals 3 and 4 (see. Fig. 16.32) the door trim. Make sure that the protective film is properly and securely attached to the door. Place the door trim to the door and connect the electrical connectors of the central locking switch, the lamp lights up when you open the door, anti-theft alarm and speakers. Ensure that all connectors are explicitly stated locking projections. Output wire from the electrical connector for the power window switch through the hole to install the switch. Connect the cable of the internal handle of opening of a door so as to hook the cable located on top. Attach the cable cover in the guide clamp 1 2 (see. Fig. 16.33). Skip cravings door lock knob through the hole in the upholstery. Ask the assistant to insert a door trim on the door at the same time, pressing the trim to the door, slide it down until it snaps into clips. Be sure to press the door trim clips in 4 (see. Fig. 16.32). Connect the power window switch to an electric socket and set the switch to trim until it snaps into its lock 2 (see. Fig. 16.30, 16.31). Replace the two screws 2 (see. Fig. 16.32) fastening the door trim and tighten them to a torque of 1.5 Nm.
| 
