REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Accent (2000 release)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Hyundai
	Accent
		Instructions
		Engine
		Greasing system
		Cooling
		Control, reduced toxicity
		Fuel system
		Ignition system
		Coupling
		Transmission
		Axes and power shafts
			Technical data
			Drive shaft
			Drive shaft with SHRUS ball and Birfield type
			Drive shaft with SHRUS Birfield and tripoidnogo type
			A rotary fist and a nave of a forward wheel
			Rear axle
			Troubleshooting
		Suspension
		Steering
		Brakes
		Body
		Air
		Electrical equipment
		Appendix
		Wiring

printable version

Drive shaft with SHRUS Birfield and tripoidnogo type

1 - ctopornoe ring;
2 - SHRUS tripoidnogo type;
3 - ctopornoe snap ring;
4 - support rollers tripoidnogo connection;
5 - a protective cover;
6 - a collar;
7 - a collar;
8 - a nut, 220-260 N ??? m;

9 - dustproof ring;
10 - CV joints Birfield;
11 - a protective cover;
12 - a collar;
13 - a collar;
14 - Dynamic damper;
15 - Dynamic damper clamp.

Dismantling

A warning

Do not disassemble SHRUS type Birfield.
For lubrication of constant velocity joints, use only special grease.
When assembling SHRUS necessary to establish new collars.

PERFORMANCE ORDER

	1. Remove the clamps and pull the protective cover from the ball SHRUS drive shaft.
A warning Be careful not to damage the protective cover.
	2. Special pliers, remove the retaining ring and hammer through a brass core bring down support rollers tripoidnogo connection with the drive shaft.
A warning When removing the bearing rollers tripoidnogo connection with the drive shaft, do not install a brass rod on the rollers.
3. Clean the support rollers tripoidnogo connection.
4. Remove the clips and pull the protective covers of the ball and SHRUS SHRUS Birfield.
	A warning If the dust cover is to be reused before removing the cover for its protection, wrap the drive shaft splines with tape.

Check

PERFORMANCE ORDER

1. Check the drive shaft splines.

2. Check for signs of rust, water and foreign objects in the boot band Birfield.

3. Check the support rollers tripoidnogo connections for wear or corrosion.

4. Check the groove inside SHRUS Birfield for wear or corrosion.

5. Check the dynamic damper for damage.

Assembly

PERFORMANCE ORDER

1. Before installing the cover wrap to protect the drive shaft splines from tripoidnogo joint with adhesive tape.
2. Grease the drive shaft and install the cover. Grease SHRUS Birfield: Centoplex 278M / 136K TJ Grease tripoidnogo SHRUS: KLKTJ41-182 (MS511-50, KOREA KLUBER)
	3. To set the dynamic damper position SHRUS Birfield in a straight line relative to the shaft, the damper position at a distance of 437 ?� 3 mm and secure it with a clamp.
4. Put grease in a protective cover tripoidnogo SHRUS and set the cover on the hinge. Protective Case tripoidnogo hinge: The total amount of grease: 95 ?� 6 g Hinge: 60 ?� 3 g Protective cover: 35 ?� 3 g
5. Add the SHRUS Birfield much grease as it was wiped out during the inspection of the hinge.
6. Install the covers.
7. Secure the protective cover SHRUS Birfield collars.
	8. Attach the covers so that the length of the drive shaft correspond to the required values The length of the left drive shaft: With a manual transmission: 645,2 ?� 2 mm With automatic transmission: 648,9 ?� 2 mm The length of the right drive shaft: With a manual transmission: 930,5 ?� 2 mm With automatic transmission: 934,2 ?� 2 mm.

« previos page
Drive shaft with SHRUS ball and Birfield type

next page »
A rotary fist and a nave of a forward wheel