add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Accent (2000 release)

general info. full specifications. diagnostics. hints. tips. tricks
Hyundai Accent
Home
 
Hyundai
Accent
Instructions
Engine
Greasing system
Cooling
Control, reduced toxicity
Fuel system
Ignition system
Coupling
Transmission
Axes and power shafts
Suspension
Technical data
Lower arm front suspension
Replace the lower arm bushing
Replacement of the plug (G) of the lower arm
Front stabilizer
Rear strut
Replacing the rear trailing arm bushings Rear suspension
Replacing the rear control arm bushing (A and B) of the rear suspension
Rear anti-roll bar
The corners of the front axle
Adjustment of a convergence of back wheels
Tyre wear
Anti-skid chains
Runout
Tightening the wheel nuts
Shift of wheels
Check withdrawal and course instability of the car
Caring for aluminum alloy wheels
Troubleshooting
Diagnosis tire wear
Steering
Brakes
Body
Air
Electrical equipment
Appendix
Wiring
 


Hit Counter by Digits


print page printable version

Suspension



Damper strut front suspension

1 - lower spring seat;
2 - dust cover;
3 - the upper spring seat;
4 - suspension strut;
5 - Self-locking nut to 60-70 N ??? m;
6 - dust cap;
7 - a nut, * 20-30 N ??? m;
8 - a spring;
9 - strut front suspension;
10 - a nut, 75-90 N ??? m.

A warning

* Marked nut which must be tightened to torque only after setting the vehicle on its wheels.


Withdrawal

PERFORMANCE ORDER
1. Remove the front wheel.
2. Separate the bracket of a brake tube from brake strut front suspension.

A warning

Do not tear or damage the brake pipe.


3. Remove the upper mounting.
4. Loosen the nuts and remove the bolts attaching the stand to the steering knuckle and remove the rack from under the wing of the car.
5. Install in the reverse order of removal.

Dismantling

PERFORMANCE ORDER
1. An edge of a flathead screwdriver to remove the dust cap.
2. The special adaptation compress a spring strut front suspension.

A warning

For the spring, use only reliable tool.


3. Loosen the lock nut at the top of the damper rod.
4. Remove the support bar, the upper spring seat, coil spring, dust cover and the lower spring seat.

Check

PERFORMANCE ORDER
1. Check the bearing support of a rack for wear or damage.
2. Check the rubber parts for damage or deterioration in their condition.
3. Check the coil spring in the absence of depression and loss of elasticity.
4. Check the damper as follows:

a. Grasp the shock-absorber rod a few times and push and pull it out of the shock absorber;
b. check that the rod moves smoothly, without jamming, and the force applied to the rod, does not change with each turn;
c. make sure that when the rod no extraneous noise.

Assembly

PERFORMANCE ORDER
1. Install the lower spring seat so that its tabs into the holes in the spring plate.
2. Replace the shock absorber dust cover.
3. The special adaptation compress a spring strut front suspension. After a complete spring set it to shock.

A warning

Set coil spring markings directed to the hinge.


4. Fully extend the shock-absorber rod and set the upper spring seat and a support strut.

A warning

Align the D-hole in the upper spring seat with the flats on the damper rod.


5. Position the upper and lower ends of the coil spring, setting them in the recess, and screw the self-locking nut, but do not tighten it completely.
6. Remove the adaptation for spring compression.
7. Tighten the self-locking nut required torque.

Torque: 60-70 N ??? m

8. Lubricate the upper bearing strut and install the dust cap.

A warning

Make sure that the lubricant is not got to support racks rubber parts.






« previos page
Troubleshooting
next page »
Technical data

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.