Code | Element | | Probable Cause |
P0713 | Oil temperature sensor | Open circuit | Damage to the sensor |
P0712 | If the sensor output voltage is more than 4.57 in 10 minutes (if the oil temperature does not increase), it is considered that there is an open in the sensor and recorded code P0713 | | Damage to the connector |
P0715 | Sensor input speed If you do not detect any pulse output from the sensor input speed on the 1st or 2nd gear, when the 3rd gear at a speed of 30 km / h is believed that the chain has an open or short circuit and will be recorded code P0715. If there is a written code P0715 four times, third gear transmission will be blocked and the control lamp N will flash at a frequency of 1 Hz. | Short circuit / open circuit | Damage to the sensor Damage of the downshift Damage to the connector Damage TCM |
P0720 | Speed sensor output shaft If the output signal from the speed sensor output shaft 50% lower than the speed of the car on the first or when the 3rd or 4th transfer rate of more than 30 km / h, it is believed that the chain has an open or short circuit and will be written code P0720. If there is a written code P0720 four times, third gear transmission will be blocked and the control lamp N will flash at a frequency of 1 Hz. | Short circuit / open circuit | Damage to the throttle position sensor Damage to the connector Damage TCM Damage to the solenoid valve |
P0703 | Brake light switch If the circuit breaker
brake lights lit more than 5 minutes when the vehicle is believed that the chain has an open or short circuit and will be recorded code P0703. | Short circuit / open circuit | Damage to the switch
stoplights Damage to the connector Damage TCM |
P0750 | Solenoid valve is a low transmission and reverse gear | Short circuit / open circuit | Damage
solenoid valve Damage Damage TCM connector |
P0755 | Solenoid valve overdrive | Short circuit / open circuit | Damage
solenoid valve Damage to the connector Damage TCM |
P0760 | Solenoid valves of the second transmission | Short circuit / open circuit | Damage
solenoid valve Damage to the connector Damage TCM |
P0765 | Solenoid valve downshift If the solenoid valve resistance is too high or too low it is believed that the chain has an open or short circuit and will write the appropriate code. As a reliable criterion will be blocked 3rd gear and warning lamp N will flash at a frequency of 1 Hz. | Short circuit / open circuit | Damage
solenoid valve Damage to the connector Damage TCM |
P0743 | Damper clutch solenoid valve (DCC) | Short circuit / open circuit | Damage
damper clutch solenoid valve Damage to the connector Damage TCM |
P0740 | Damper clutch solenoid valve (DCC) If the resistance is too small solenoid valve is considered that the chain has an open or short circuit and will be recorded code P0743. If the load factor of the solenoid valve actuator damper clutch control - 100% for a continuous period of more than 4 seconds, it is considered that there is damage to the damper clutch control system and is written code P0740. If we write the code P0743 will be blocked 3rd gear and warning lamp N will flash at a frequency of 1 Hz. | Faulty system | Damage
damper clutch solenoid valve Damage to the connector Damage TCM |
P0731 | Gear ratio 1st gear does not meet specifications If the output from the sensor output shaft speed multiplied by the gear ratio of the first transmission does not match the output from the sensor input speed will be recorded code P0731. If there is a written code P0731 four times, third gear transmission will be blocked and the control lamp N will flash at a frequency of 1 Hz. | | Damage to the sensor input speed Damage to the sensor output speed Damage to the low brake transmission and reverse gear Damage to clutch downshift |
P0732 | Gear ratio of the second transmission does not meet the specifications If the output from the sensor output shaft speed multiplied by the gear ratio of the second transmission does not match the output from the sensor input speed will be recorded code P0732. If there is a written code P0731 four times, third gear transmission will be blocked and the control lamp N will flash at a frequency of 1 Hz. | | Damage to the sensor input speed Damage to the sensor output speed Damage to clutch downshift Damage to the coupling of raising transfer |
P0733 | The gear ratio of 3 transfers does not meet specifications If the output from the sensor output shaft speed multiplied by the gear ratio of 3-second transmission does not match the output from the sensor input speed will be recorded code P0733. If there is a written code P0731 four times, third gear transmission will be blocked and the control lamp N will flash at a frequency of 1 Hz. | | Damage to the sensor input speed Damage to the sensor output speed Damage to the brake 2nd gear Damage to the coupling of raising transfer |
P0734 | The gear ratio of 4th transfer does not meet the specifications If the output from the sensor output shaft speed multiplied by the gear ratio of the fourth transmission does not match the output from the sensor input speed will be recorded code P0733. If there is a written code P0734 four times, third gear transmission will be blocked and the control lamp N will flash at a frequency of 1 Hz. | | Damage to the sensor input speed Damage to the sensor output speed Damage to the low brake transmission and reverse gear Damage to clutch the reverse gear |
P0736 | Gear ratio of reverse gear does not meet specifications If the output from the sensor output shaft speed multiplied by the gear ratio of the reverse gear does not match the output from the sensor input speed will be recorded code P0733. If there is a written code P0734 four times, third gear transmission will be blocked and the control lamp N will flash at a frequency of 1 Hz. | | Damage to the sensor input speed Damage to the sensor output speed Damage to the low brake transmission and reverse gear Damage to the brakes reverse gear Damage to clutch the reverse gear |
P1723 | Relays A / T If the voltage on the control relay A / T less than 7 V after the ignition is switched, it is believed that the chain has an open or short circuit and will be recorded code P1723. Pinion 3rd gear will be locked and the indicator lamp will blink N at 1 Hz. | Short circuit / open circuit | Damage
relays A / T
Damage to the connector
Damage TCM |
P0708 | SWITCH RANGES TRANSMISSION No signal for more than 30 seconds More than two signals arrive continuously for more than 30 seconds | | Damage to the transmission range switch |
