 printable version
Controls, instrumentation and equipment
| Fig. 1.20. Controls, devices and equipment 1 - Side air vents; 2 - the switch of heating of back glass; 3 - light switch; 4 - a combination of devices; 5 - switch wiper and washer; 6 - switch hazard warning lights; 7 - clock; 8 - central air vents; 9 - the glovebox; 10 - the switch of the air conditioner; 11 - cigarette lighter; 12 - cassette recorder; 13 - the block of management of a heater / air conditioning; 14 - ashtray; 15 - the choke (petrol engine); 16 - the switch of a washer of headlights; 17 - the switch of a cleaner and a washer of back glass; 18 - a regulator of illumination of devices; 19 - button unlocking the bonnet; 20 - the switch of position of an external rear-view mirrors with the electric drive; 21 - control shock absorbers
|
Location instruments and controls shown in Fig. 1.20.
| Fig. 1.21. Combinations of devices with analog devices (Type A): 1 - a tachometer; 2 - control lamps of the direction indicators / hazard warning lights; 3 - coolant temperature; 4 - fuel gauge; 5 - speedometer; 6 - Total mileage; 7 * - the counter of daily run; 8 * - reset button for trip counter; 9 - indicator lamps
|
The appearance of combinations of analog devices is shown in Fig. 1.21, the combination of electronic devices is shown in Fig. 1.22.
| Fig. 1.22. Instrument cluster with electronic devices (type B): 1 - button for switching the display range; 2 - control lamps of the direction indicators / hazard warning lights; 3 - fuel gauge; 4 - tachometer; 5 - speedometer; 6 * - the counter of daily run; 7 - coolant temperature; 8 - Total mileage; 9 * - reset button for trip counter; 10 - the counter of daily run; 11 - indicator lamps
|
NOTE The list of controls and instrumentation depending on the vehicle or installed on request. |
Speedometer. It shows vehicle speed in km / h.
Total mileage. The counter indicates the total mileage of the car.
The counter of daily run. Shows run it after the last reset.
Reset button for trip counter. Pressing the button to reset the counter.
Control lamps direction indicators / hazard warning lights. If the indicator lamps of the direction indicators are not functioning properly, then the system of the direction indicators is defective. The fault must be removed as quickly as possible. Both indicator lamps of the direction indicators light up at the same time, if the system is switched on the hazard warning lights.
Coolant temperature. It shows the temperature of the coolant in the engine cooling system. For type A: if the arrow pointer will go beyond the normal range, it means that the engine is overheated.
| Fig. 1.23. Normal temperature zone (A) shows an electronic engine coolant temperature gauge
|
For Type B: when the engine overheated all zones are flashing indicator (Fig. 1.23). In case of overheating of the engine, take the following measures. 1. Stop the car on the roadside. 2. Turn off the air conditioner. 3. Stop the engine if the coolant or steam coming out of the radiator. Turn the ignition key back to position ?�ON?� (?�II?�), without starting the engine. In this position, the ignition fan operates in automatic mode. If it does not work, consult your service workshop Car Mazda. 4. If the coolant comes out, leave the engine idling for more efficient cooling, open the hood. 5. If the engine is idling the temperature decreases, stop the engine and wait until it cools down.
A WARNING When fault coolant temperature signal is in the form of flashing zones "H" (130 ?� C) and "C" (50 ?� C). Take as soon as possible the necessary measures to eliminate the cause of the fault (only on vehicles with electronic devices). |
6. Check the hose of a cooling liquid in the joints for leaks. Stop the engine immediately if you detect a leak of coolant. 7. Check the coolant level, if there is no leaking. If necessary, add recommended coolant.
The fuel gauge. The fuel gauge indicates how much fuel is in the fuel tank. Tank capacity 60 liters.
A WARNING For Type B: if it starts flashing the lowest zone index, it means that the fuel level in the tank has dropped to about 5 liters. |
When fueling the ignition is turned off, it may take considerable time until the indicator set to the desired level of fuel. Therefore, switch off the ignition when fueling. When malfunction fuel level indicator signal is a flashing segment "F" ("1") and ("0"). Take as soon as possible the necessary measures to eliminate the cause of the fault.
Warning lights
A WARNING Warning lights can be checked, if you turn the ignition key to ?�ON?� (?�ll?�), without starting the engine and apply the parking brake. If the warning lights do not burn, they must be checked by the maintenance of cars Mazda. |
 Control lamp of inclusion of a headlight. It illuminates when the high beam.
 The warning lamp battery charging. It illuminates when the ignition is switched on and goes out after starting the engine. The generator drive by the durable belt. If during movement control lamp, you must proceed as follows. 1. Stop the car. 2. With the engine running, check belt tension and condition. 3. If the V-belt is OK, then the fault is in the system of charging the battery. It is recommended that as soon as possible to determine the fault and pass a car dealer to fix the problem.
 The indicator lamp insufficient brake fluid level and the parking brake. Warning signal, apply the parking brake. If the parking brake and the ignition warning light. It should go off when the parking brake is off. The alarm level of brake fluid. If the lamp lights up after turning the parking brake with the ignition on, it means that the brake fluid level in the reservoir is too low. If the warning light comes on while driving, proceed as follows. 1. Check whether the parking brake lever is lowered. 2. If this is the case and the control lamp remains lit, gently stop the car on the roadside. 3. With the engine running, check immediately whether the brake fluid level and add fluid if necessary. Check out all the elements of a hydraulic drive of the brake system for leaks. 4. If there are any leaks or faulty seat brake warning lamp will continue to burn - the movement of the vehicle can not continue. The vehicle must be towed to the dealer of cars Mazda, to check the brake system and carry out the necessary repairs.
A WARNING If the brake fluid level is too low, you should immediately find the nearest service center to check the service braking system. While driving need to press hard on the brake pedal when braking, and to consider the possibility of increasing the braking distance and pedal free travel. |
 The warning lamp turn on the hazard warning lights. Lights when the emergency light alarm system. At the same time all direction indicators flash.
 The control lamp of insufficient oil pressure. Illuminates when the oil pressure is below the limit. If this motion lights warning lamp, stop motion, stop the engine, check the engine oil level and if necessary to bring it to normal. If the warning lamp lights up, despite the fact that the engine oil level is normal, you can not keep going. Do not run the engine even at idle - need care.
A WARNING If the above instructions are not complied with and the car continues to operate, and further, the engine can be severely damaged. |
 The warning lamp and warning sound to insufficient fuel level. The warning lamp and warning sound to insufficient fuel level are activated when the fuel tank is about 10 liters of fuel.
 The indicator lamp bulb burnout stoplight. When the lamp burns out a stoplight or a fault occurs in an electrical circuit stop signal warning lamp lights up. Immediately repair.
 Control lamp of level of liquid in the washer tank. The control lamp lights up as soon as the liquid level in the tank windshield washer falls to the lowest level. Check the fluid level and add fluid if necessary.
 The warning lamp switch to a higher gear. If this warning light comes on, it means that fuel consumption on a gear is excessively large. In this case, in order to reduce fuel consumption shift the transmission to the next higher gear.
 The indicator lamp excessive force pressing the accelerator pedal. This warning light illuminates when the accelerator pedal is pressed too. In this case, in order to reduce fuel consumption releases the accelerator pedal until the lamp is extinguished.
 The warning lamp turn on the rear fog lamp. This warning light illuminates when the rear fog lamp.
 The warning lamp the air damper. The warning lamp lights up when the outstretched arm choke.
 The indicator lamp bulb blown rear position lamp. If this warning light comes on, it means not functioning taillight or damaged electrical circuit. It is necessary to solve the problem immediately.
The indicator lamp cold start (diesel engine). The warning lamp lights up when the elongated handle cold start of the diesel engine.
 The warning lamp / warning light coolant level (for diesel engines). With the ignition on, this warning lamp lights to control the functioning of incandescent and should go out after starting the engine. If during movement warning lamp or a warning signal, follow these steps. 1. Stop the car on the roadside. 2. Turn off the engine and let it cool. If there is no coolant leaks, check the coolant level in the expansion tank and radiator. If necessary, add coolant. 3. If the warning light does not go out and drag the car to the nearest service workshop Car Mazda.
A WARNING Since the engine is made of aluminum alloy, be sure to use antifreeze based on ethylene glycol. |
The warning lamp / warning about the water separator (diesel engine).
| Fig. 1.24. Switching the fuel gauge on the lower range of 5-15 liters by pressing ?�SCALE CHANGE?�
|
Switching display range fuel level indicator (only in combination of electronic devices). If you press the ?�SCALE CHANGE?�, will show lower range of fuel level indicator 5-15 l in the extended form (Fig. 1.24). After about 5 to happen to switch back to the normal count.
| Fig. 1.25. Location trip counter (1) and the (2) in the switching combination of electronic devices
|
The counter of daily run (only in combination of electronic devices). With the counter you can measure two different track section. If you press the button will switch between the readings of "A" and "B" (Fig. 1.25). Indication "A" (or "B") can be set back to zero if about 1 to hold down the reset button. You can, for example, use one counter for measuring the fuel consumption and the other counter to measure the distance traveled. Indications daily run in km correspond to the speedometer.
Tachometer. Specifies the frequency of engine speed in thousands of revolutions per minute.
A WARNING ???� ?????�?�???�?????�?� ???�?�???�?�?�?? ?????????�?�?�?�?? ?? ?????�???????? ???�???�?????� ?�?�?�?????�?�???� ??� ???�?? ?????�?�?� ???�?�???�?�?? ?????????�?�???�?????� ?????????�?�?�?�?? ?? ?�???�?�?�?�???? ???????�?�?????�??????????. |
???????????� ???�?�?�?�???????????????? ?�?�?????� ???�?????�?�. ???�?????� ???�?????�???�?�?�???? ???????�?� ???�?�?????????�?????? ???� ???�?�?? ???????????? ???�?�?�?�???????????????? ?�?�?????� ???�?????�?� ??� ???�?????� ?????????�???�???�?�?�???? ???� ?�?�?????????????? ?????�?????????�???� ?? ?????? ???�?????�?????�?? ???????�?????� ?????????????�?�?�???? ?????�???�. Unlock the lock of the bonnet and lift it up. Fix the hood support rod in the open position. Before closing the hood support rod, set back in the holder. Lower the bonnet and allow it to enter the lock.
Adjusting the backlight dashboard.
| Fig. 1.26. The direction of rotation of the knob to zoom in (a) or decreasing (b) brightness dashboard
|
Turning the knob to set the brightness of the instrument panel (Fig. 1.26). Switch heated rear window. Rear window heater when the ignition (key in the position of the ignition switch ?�ON?� / ?�II?�) can be enabled by pressing the switch. When the heated rear screen warning light.
A WARNING To clean the rear window from the inside does not use sharp or abrasive cleaning agents, as a result, the wire can damage the heating elements. |
The switch of a cleaner and a washer of back glass.
| Fig. 1.27. The switch of a cleaner and a washer of back glass: 1 - Only windshield wiper switch; 2 - switch wiper and washer; 3 - Only windshield washer switch
|
Wiper and washer, rear window included the switch shown in Fig. 1.27.
A WARNING If the washer does not work, check the washer fluid reservoir. |
Clock. To set the time, turn the key in the ignition switch to ?�ON?� (?�II?�). If you press the ?�RESET?� (return), the minute display is set to zero. When the button is released will be set full hour. For example, if the button is pressed in between 0:01 and 9:29, the indication will change to 9:00. Between 9:30 and 9:59, it will change to 10:00. Similarly, you can set the time, for example, to a time signal transmitted by radio. If the button is pressed ?�HOUR?�, the clock setting. If the button is pressed ?�MIN?�, will change the minute.
Switch headlight washer. The cleaning fluid is sprayed onto the lenses of headlights, if the switch is turned on with the ignition.
The regulator damper. Adjustable dampers can be installed in three different positions: ?�SPORT?�, ?�NORMAL?� and ?�AUTO?�.
A WARNING Headlights can not include more than 10 seconds. |
To improve the dynamic properties of all shock absorbers are set to ?�SPORT?�. In this case, the switch is ?�SPORT?� front and rear shocks are set "tough." In order to ensure smooth soft dynamic properties (mode ?�NORMAL?�) all shock absorbers are installed "soft". Automatic adjustment (mode ?�AUTO?�) has the following functions. Stability at high speed. In order to improve the dynamic properties of the front shock absorbers are installed into the "tough" if it reached a speed of about 80 km / h. If the drive speed is reduced to about 60 km / h, this setting is removed again.
Position switch | Shock absorber | front | rear | Included | Hard | Fine | Included | Fine | Fine |
Swing to the transversal axis when braking. To prevent oscillation about the transverse axis during braking all the dampers are installed into the "tough." Keeping a vehicle rollover. In the steering wheel and the vehicle speed is determined by the lateral force. Above a certain value of the shock absorbers are set to mode "hard" to prevent tipping.
Cigarette lighter. The cigarette lighter is activated by pressing on it until it locks. After heating it with a mouse back in position and can be used. To be able to use the cigarette lighter with the engine off, the key is in the ignition switch, turn to the "ACC?� (?�I?�). Ashtray. To remove the ashtray from the socket pull it forward until it stops and press down on the retaining spring. If you are not using the ashtray, close it.
A WARNING Do not use the ashtray for garbage collection. |
Closed storage compartment under the steering column. The box can be opened, if the pull-down box for recessed handle. Glovebox. To open the glove box, pull down the lid. If the cover has a lock, insert the key and turn it to the left to open the lid.
| 
