 printable version
Poddomkrachivanie / hanging and an emergency transportation vehicle
Poddomkrachivanie using staff and Jacks, tire repairs  | Staff jack is only intended for short-term recovery of the car when replacing wheels; before carrying out any work underneath the car you need to install it on special props! When using small-sized spare wheel (T105 / 70D14) is not allowed to move at over 80 km / h, as In this case, the wheel may break. |
| - Park the car on an equal horizontal platform, whenever possible with a firm covering.
- Cock a lay brake and set the selector lever to position AT ?�P?� (on models with AT) or select first or reverse gear (on models with Manual transmission).
- If necessary, turn on the alarm and set warning triangle.
- Prop chock wheel located on a diagonal from the to be replaced.
 | When performing the procedure on a slope should enclose shoes under both wheels intact axis by descent. |
- Prepare jack, wrench and spare tire (the jack and spare tire is stored underneath the floor panel in the luggage compartment).
- With proper configuration, remove the protective cap of the disc, and then take one turn the nuts of the failed wheel.
 | - Get into the head of the jack under the corresponding point under the sill beam (the illustration shows the point of jacking and installing safety net of support) - make sure that the jack is positioned vertically, while his heel rested against the ground over its entire surface, - with loose ground sheet under the heel of the right pad ( winter is useful to have in the car a piece of wide boards). Watch out also for the fact that the groove in the head of the jack went in the corresponding edge in the threshold of the car.
|
| Regardless of the slope jack must always hold upright position! |
- Working jack handle, lift the car - damaged wheel must be completely off the ground.
- Completely give the wheel nuts and make replacement wheel.
- Check the inflation pressure of the wheel mounted, if necessary, make appropriate adjustment (see. Specifications).
- Remove to remove a wheel and tools to their regular places.
- Finally, tighten the wheel nuts evenly in a diagonal manner with a force of about 113 N ??? m.
 | - The reference point when using Jacks indicated in the illustration.
|
|
|
Hanging car | It is not allowed in any case, be inspired car on the power unit, front and rear suspension, as wherein said structure can be seriously damaged. |
For hanging car uses the platform or lift with four legs, rests on the point of installation safety net supports (see. Illustration | Between the support or lift platform and reference point set accordingly lining LM4519-0000 or LM4086-0200. |
Transportation emergency vehicle Transportation platform tow truck Wise to the emergency vehicle to transport it to the tow truck. This transportation can be made: - The method of complete loading a defective vehicle on a tow truck platform;
- The method of partial loading (front axle to the towing pendant shelf and the rear or on a special cart or on the ground). In this parking brake must be released.
Preparations for towing |  | - Front removable lug for attaching tow line is screwed into the hole located under a flap on the left side of the bumper. To remove the plug gently press the top edge of the bumper with a screwdriver. For screwing lug is convenient to use a key for the wheel nuts.
|
 | - The rear towing eye is welded under the rear bumper on the right.
|
- Before starting to tow damaged cars should turn on the ignition, set the transmission into neutral and release the parking brake.
- Wise to produce a rigid towing bar. When towing a flexible coupling, use only specially designed for this purpose, the elastic rope.
- Before driving, the drivers of both vehicles (towing and towed) should agree with each other route.
|
|
Towing with a view to starting the engine | Pre try to start the engine from the auxiliary battery. Starting models with AT by towing or pushing is not valid, and on models with Manual transmission this may damage the catalytic converter - distance towing with the aim of starting the engine must not exceed 50 m. |
| - Turn on the 2nd or 3rd gear, depress the clutch pedal and hold it, turn on the ignition.
- When both cars are moving, slowly turn the clutch (release the pedal).
- Once the engine has started, depress the clutch pedal and turn off the transmission, so as not to collide with the towing vehicle.
|
|
Emergency Towing vehicle | Towing without oil in the transmission is not allowed without interrupting the drive wheels off the ground. |
The driver of the towing vehicle must try to move as evenly as possible, gradually releasing the clutch when shifting gears and particularly when pulling away. In managing the towed vehicle, make sure that in the course of movement remain permanently taut rope, try to avoid sudden jerks and arrivals on Loose cable. Remember that when the engine is switched off the braking performance of the car is markedly reduced due to the fact that it ceases to operate the brake servo. It should squeeze the brake pedal is working with much more than usual force; when performing maneuvers have to exert a greater force as the steering wheel, as power steering also does not function. The movement should be carried out along the shortest route. Faulty car with AT authorized to tow a maximum speed of 50 km / h and at a distance of not more than 65 km. Observe traffic rules, avoid sudden braking, acceleration and excessive maneuvering. Remember that when towing a car on the edge of the dirt road is always a danger of demolition by the wayside. Before the start of the towing vehicle with defective AT check the transmission fluid level (see chap. Adjustment and car routine maintenance), - with insufficient ATF, should correct it or tow the car with only detached from the ground wheel drive.
|
