add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Nissan Micra (2002 model year)

general info. full specifications. diagnostics. hints. tips. tricks
Nissan Micra
Home
 
Nissan
Micra
Introduction
Controls and operation receptions
Options and car routine maintenance
Engine
The engine cooling system, heating, ventilation and air conditioning
The power supply system and exhaust
Systems of an electric motor
Manual box of a gear change and clutch
Automatic Transmission
Drive shafts, steering knuckles and Hub assembly
Brakes
General information and safety measures
Removing and installing brake lines
Removing and installing brake pedal
Removal and installation of the GTZ
Removal and installation of the vacuum amplifier
Replacing the brake pads of the front wheels
Removing and installing the front brake and brake discs
Removing and installing rear brake assembly
Removal and installation of the parking brake
Removal and installation of components of system ABS
Suspension and steering
Body
Onboard electric
Diagrams
 


Hit Counter by Digits


print page printable version

Brakes



Specifications

Overview

brake system With dual diagonal division of contours, front disc (calipers with single) and rear drum brakes
The type of fluid FMVSS 116 DOT 4 and DOT 3 or (not to be mixed fluid DOT 4 and DOT 3)
Progress handbrake
  • When force 196 N
11 ÷ 12 clicks
  • Full
15 clicks
The diameter of the GTZ, mm 23.81
Lifting height brake pedal (Manual transmission models with AT //) mm 161 ÷ 171 171 ÷ 181 //
Lifting height brake pedal is pressed when the engine is running with a force of 490 N (models with Manual transmission // AT), mm, not less 80 // 85
The gap between the rubber stopper and the end of the pedal D / stoplights, mm 0.74 ÷ 1.96
The free pedal travel, mm 3 ÷ 11
Permissible loss of vacuum in the control valve (from -66.7 kPa), kPa 1.3 to 15 seconds

Front brake

Type CL22, disk ventilated
// Nominal minimum permissible thickness of the brake discs, mm 22 // 20
// Nominal minimum permissible thickness of the brake shoe linings (unsupported), mm 12.4 // 2.0
The outer diameter of the brake disc, mm 260
The maximum permissible roughness of the brake disk, mm 0.03
Maximum permissible palpation of a brake disk mounted on the car, mm 0.058
Bore mm 53.95

Rear brake

Type LT20, drum
Nominal // maximum allowable inner diameter of the brake drum, mm 202 // 203.2
// Nominal minimum permissible thickness of the brake shoe linings (unsupported), mm 4.5 // 1.5
// The length of the brake linings width, mm 195 // 38
The diameter of the cylinder, mm 19.05

Servo

Type E52 / 5/255
The diameter of the aperture, mm 254
Installation size of the input shaft, mm 158.25
Permissible loss of dilution (from -66.7 kPa), kPa 3.3 to 15 seconds

Efforts of a tightening of carving connections, N ??? m

Brake hoses to the caliper 18
Fasteners brake tubes 16.2
Nuts of fastening of the pedal assembly 21
Bolts anchor bracket 105
Caliper mounting bolts to the anchor bracket 35
Bleeder valve 10
Mounting the brake disc 13.9
Bolts rear wheel cylinders 9
Fastening assembly handbrake 21.5
Mounting brackets Brake Cable 5.3
Fastening wheel sensors 21.6
Activator bracket bolts and ABS control unit 12.8
Bolts activator and the ABS control unit to the bracket 8




« previos page
Removing and installing the hub of the rear wheel assembly
next page »
General information and safety measures

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.