 printable version
The control body dimensions
general information In the automotive industry can be used two ways to control the size of removing the support points between the elements of the body / chassis: direct and projection. In the first case, measured by the shortest distance between the selected point on the straight line connecting them. In the second case it is determined by the length of the projection of the line on a certain dimensional - usually horizontal - plane. The two main ways are used in the automotive control the size of removing the support points between the elements of the body / chassis 
The following section provides an illustrative material for removing control the size of the table and their nominal values.  | All figures are taken directly, unless the contrary is specifically stated otherwise. |
Control the size of front end (all models) | A, A ' | Holes for the rear wing bolts (Ø 10 mm) | | B, B ' | Holes boltykrepleniya front wings (Ø 10 mm) | | FROM | Nut brake line (Ø 6 mm) | | D, D ' | Nuts of fastening of the block range (Ø 9.8 mm) | | E, E ' | Support welding holes (left: Ø8h10 mm, right: Ø 8 mm) | | F | Hole for fixing harness (Ø 7 mm) |
| Room measurement | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | | Nominal value mm | 1293 | 696 | 1257 | 696 | 1452 | 930 | 1057 | 993 | 1103 | | Room measurement | 10 | eleven | 12 | 13 | 14 | 15 | | | | | Nominal value mm | 995 | 1140 | 282 | 1000 | 282 | 1104 | | | |
The lateral size of the control (5-door models) 
| A | Top support hole amplifier side frame (Ø 8 mm) | | AT | The lower support hole amplifier side frame (Ø 7x10 mm) | | FROM | Upper hole for fastening the upper hinge straps of the front door (Ø 12 mm) | | D | Lower hole for fixing the lower hinge of the front door trims (Ø 12 mm) | | E | Upper hole for fastening the upper hinge strap back door (Ø 10 mm) | | F | Lower hole for fixing the bottom hinge rear door trims (Ø 12 mm) | | G | Hole for fixing the gauge-switch of a back door (Ø 15.8 mm) | | H | Hole for fastening the rear door sill plates (Ø 8.5 mm) | | I | Hole for fixing the rear bumper |
| Room measurement | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | | Nominal value mm | 110 | 889 | 1992 | 2000 | 912 | 898 | 921 | 380 | 1113 | | Room measurement | 10 | eleven | 12 | 13 | 14 | 15 | 16 | 17 | 18 | | Nominal value mm | 1169 | 1177 | 1114 | 360 | 924 | 1493 | 763 | 991 | 1474 | | Room measurement | 19 | 20 | 21 | 22 | | | | | | | Nominal value mm | 617 | 557 | 606 | 888 | | | | | |
Internal control and the cabin size (5-door models)  | A, A ' | Upper hole mount wiring harnesses on the inside racks (Ø7 mm) | | B, B ' | The lower hole mounting wiring harness on the inside uprights (Ø 7 mm) | | C, C ' | Holes for fixing finishing (Ø 14 mm) | | D, D ' | Holes for fixing panel carpeting (Ø 6 mm) | | E, E ' | Holes for the anchor nodes seatbelt (Ø 9 mm) | | F, F ' | Holes for fixing the module cooler (Ø 9 mm) | | G, G ' | Holes for fixing the return mechanism seat belts (Ø 18 mm) | | N, N ' | Holes for fixing finishing (Ø 6 mm) | | I, I ' | Holes for fixing drummers rear door locks (Ø 12 mm) | | J, J ' | Holes for fixing wiring harness (Ø 5 mm) |
| Room measurement | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | Nomination
Flax value mm | 1118 | 1317 | 1350 | 1340 | 1177 | 1350 | 1368 | 1026 | 1480 | 740 |
Internal controls in the cabin size (5-door models) 
| A, A '; B, B '; C, C '; D, D '; E, E '; F, F '; G, G '; H, H '; J, J ' | See above. Illustration of the measurements A | | I, I ' | Support welding holes (Ø 10 mm) | | TO | Hole for mounting the parking brake lever (Ø 12 mm) |
| Room measurement | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | Nomination
Flax value mm | 1150 | 1162 | 1090 | 798 | 1158 | 978 | 718 | 1529 | 1103 | 1811 |
Internal control the size of a cabin (5-door models, the left side)  | A, A '; B, B '; C, C '; D, D '; E, E '; F, F '; G, G '; H, H '; I, I '; J, J ' | See above. In the illustration of the measurements | | TO | Hole for anchor bracket assembly belt (Ø12 mm) |
| Room measurement | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | Nomination
Flax value mm | 1681 | 1936 | 1993 | 1589 | 1258 | 1129 | 1021 | 1031 | 605 | 1035 |
Internal control the size of a cabin (5-door models, the right side) 
| A, A '; B, B '; C, C '; D, D '; E, E '; F, F '; G, G '; H, H '; I, I '; J, J '; TO | See above. Illustration of the metering, the left side |
| Room measurement | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | Nomination
Flax value mm | 1765 | 2022 | 2079 | 1695 | 1374 | 1275 | 1182 | 1153 | 852 | 1124 |
Control the size of the rear end of the body (5-door models) 
| A, A ' | Holes for fixing the loop straps (left: Ø8h12 mm, right: Ø 8 mm) | | B, B ' | Holes for fixing telescopic stops (Ø 9 mm) | | C, C ' | Support welding holes (Ø 6.5 mm) | | D, D ' | Support welding holes (left: Ø8h12 mm, right: Ø 12 mm) | | E | Hole for fixing striker tailgate (Ø 12 mm) |
| Room measurement | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | | Nominal value mm | 725 | 1111 | 574 | 1303 | 1498 | 1037 | 1303 | 406 | 1230 |
Control the size of the chassis frame (5-door models) Measurements made by the direct method 
| A | Holes support brackets Body number 1 (left: Ø28 mm, right: Ø 24 mm) | | AT | The holes in the rack supports (Ø 65.6 mm) | | FROM | Holes support brackets Body number 2 (Ø 28 mm) | | D | Drainage holes (Ø 12 mm) | | E | Holes for fastening the support brackets of the body number 3 (Ø 28 mm) | | F | Drainage holes (Ø 12 mm) | | G | Holes support brackets Body number 4 (left: Ø24h28 mm, right: Ø 28h32 mm) |
Measurements made by the projection method 
| A | Holes support brackets Body number 1 (left: Ø 28 mm, right: Ø 24 mm) | | AT | The holes in the rack supports (Ø 65.6 mm) | | FROM | Holes support brackets Body number 2 (Ø 28 mm) | | D | Drainage holes (Ø12 mm) | | E | The support beam of the fuel tank (Ø 42 mm) | | F | Holes for fastening the support brackets of the body number 3 (Ø 28 mm) | | G | Transverse tank number 5 (Ø 68.5 mm) | | H | Holes for fixing shock absorbers (Ø 19 mm) | | I | Holes support brackets Body number 4 (left: Ø 24h28 mm, right: Ø 28h32 mm) |
|
