| Type automatic transmission | 4-speed (including overdrive) manufactured by Aisin Warner |
| Designation | AW372LE |
| Type of lubrication | Pressure from the oil pump |
| Cooling system | The two-stage, with an additional heat exchanger |
| The torque converter (inverter rotation) |
| Three-element, one-stage, two-phase, with the lock mechanism |
| 19 |
| Oil pump |
| Trochoid rotor |
| From Engine |
| The gear change mechanism |
| 1-stage planetary gearbox with 4 forward gears, 1 back |
| See. Section Features of operation of vehicles equipped with a catalytic converter in chapter Controls and operation receptions |
|
- Multi-disc wet type clutches
| 3 sets |
- Multi-disc brakes wet type
| 4 sets |
| 3 sets |
|
| 2.826: 1 |
| 1.493: 1 |
| 1,000: 1 |
| 0.730: 1 |
| 2.703: 1 |
| Turns Stall-Test, min -1 | 2000 ÷ 2300 |
| The distribution of line pressure at idle and check Stall-Test | See. Section systems of electric motor |
Diagnostic Codes system electronically controlled automatic transmission, extractable via OBD II Scanner
| Bolt the gauge-switch of position of transmission (PNP) | 3.9 ÷ 6.9 |
| Plug the service line pressure test nipple | 14.7 ÷ 17.6 |
| Bolts of fastening of transmission to the transfer case | 44 |
| Bolts of fastening of transmission to the engine |
| 57 ÷ 81 |
| 69 ÷ 88 |
| Nuts support the suspension of the power unit | 69 ÷ 88 |
| Bolts reference to the frame crossmember | 31 ÷ 46 |
| Flare nuts ATF cooling pipes tract |
- On the part of the transmission
| 31 ÷ 47 |
- From the side of the radiator
| 24 ÷ 35 |
| Support bracket lines tract cooling ATF | 0.39 ÷ 0.58 |
| Bolts of fastening of the pump assembly of the AT | 6 ÷ 9 |
| Bolts of fastening of the sealing element of the pump assembly | 18 ÷ 25 |
| Bolts sections of the valve assembly | 8 ÷ 12 |
| Bolts oil guard | 5 ÷ 6 |
| Sump bolts AT | 4 ÷ 5 |
| Bolts adapter cap | 27 ÷ 42 |
| Bolt locking manual shift valve spring | 5 ÷ 6 |
| Bolt throttle cam | 6 ÷ 9 |
| Bolts reducing valve | 5 ÷ 6 |
| Bolts of the valve plate assembly | 5 ÷ 6 |
| Bolts central support AT | 24 ÷ 28 |
| Torque converter bolts |
| 27 ÷ 42 |
| 48 ÷ 68 |
| Bolts of e / m-valve switch | 6 ÷ 12 |
| Bolt e / m torque converter lockup clutch valve | 5 ÷ 6 |
| Nuts of fastening of the selector lever assembly | 18 ÷ 27 |
| Bolts of fastening of the lever of switching of modes of a distributing box | 22 ÷ 28 |
| Adjusting nut drive cable AT | 2 ÷ 3 |
| Adjusting the throttle wire nut | 15.7 ÷ 22.5 |
| The spindle bolt selector lever | 11.7 ÷ 16.7 |
| Tighten the screws on the gear lever position indicator | 2.0 ÷ 3.0 |
| Screw fastening the handle of the selector lever | 2.0 ÷ 3.0 |
