add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Passat B6 (from the year 2004)

general info. full specifications. diagnostics. hints. tips. tricks
Volkswagen Passat B6
Home
 
Volkswagen
Passat B6
Operation and maintenance of car
Engine
Transmission
Chassis
Steering Gear
Brakes
Onboard electric
Overview
Power supply system
Lighting
Removing the lights
Installing lights
Adjusting the headlights
Replacing the lamp beam
Replacing the lamp beam
Replacing the parking light bulb
Removal and installation of servo-leveling, headlamp manufacturer - Hella
Removal and installation of servo-leveling, headlamp manufacturer - Valeo
Check headlight adjustment
Check headlight adjustment via vyverochnogo screen without adjusting the 15 ?�
Adjusting headlamp with gas discharge lamps
Adjusting the main headlights with halogen lamps
Main Headlights with gas discharge lamps
Replacing gas-discharge lamp
Removing and installing front turn signal lamp
Removing and installing lighting in the door mirrors to facilitate landing
Removing and installing the rear light in the sidewall of the body
Removing and installing light plate (sedan)
Removing and installing the license plate light, station wagon (Variant)
Removing and installing bonnet contact switch
Removing and installing light switch
Removal and installation of a regulator-leveling and dimmer buttons and instrument panel
Removal and installation of a control lamp off the front passenger airbag
Removal and installation of lighting the glove box
Removal and installation of a control lamp central locking SAFE function
Replacement of ceiling lighting front of the cabin
Removing and installing center console switches
Removing and installing the main fuse box
Removal and installation of the switching unit on the left side of the engine compartment
Removal and installation of the relay unit on the left side of the front panel
General information on repair electricians of the car
Repair wire CAN bus
Broken wire with repair in two places
Repair of contacts in the connector housing
Mechanical locking connector housing
Round contacts
Flat contacts with asymmetrical locking tongues
Body
diagrams
 


Hit Counter by Digits


print page printable version

Replacing the lamp beam



NOTE
Left lamp beam and right beam bulb can check with the diagnosis of the actuators onboard supply control unit.

Withdrawal
Turn the ignition and all electrical consumers and translate the key to position 0 (pre-emphasis).

NOTE
Put the ignition key on the remote control during removal and installation into the vehicle in order to avoid blocking doors and self-activation of the ?�Coming Home / Leaving Home (home Arrival / Departure from the house)."
To replace the lamp beam must be removed adjacent parts corresponding lights.

NOTE
The illustration shows replacement of the lamp beam on the right headlight.
Replacing left headlight beam and right beam bulb the same way.



Protective cap
Fig. 7.53. Protective cap


Remove the protective cap 1 (Fig. 7.53).

Lamp holder
Fig. 7.54. Lamp holder


Loosen the cartridge with a lamp beam 1 in the direction of the arrow and pull it out of the spotlight so far as the length of the wires (Fig. 7.54).

Removing the lamp
Fig. 7.51. Removing the lamp


Remove the beam bulb 2 in direction of the cartridge 1 (Fig. 7.51).

Setting

Installing headlight low beam
Fig. 7.52. Installing headlight low beam


Plug a lamp into the socket beam so that the projection lamp 1 against the guide 2 cartridge (Fig. 7.52).

NOTE
When installing pay attention to the tight fit of the cap. Ingestion of water lights, headlamp may be spoiled.
When installing the lamp, do not touch its glass surface. Fingers are left on the glass bulb greasy fingerprints that evaporate after the lights and light the lamp may become darker.



Install the lamp socket
Fig. 7.55. Install the lamp socket


Install the cartridge with a lamp beam 1 headlight and turn the cartridge with a lamp beam in the direction of the arrow (Fig. 7.55).
Reinstall the cap.
Check the operation of lights, including all of its functions.
Check the setting of the headlights, if necessary - adjust.




« previos page
Replacing the lamp beam
next page »
Replacing the parking light bulb

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.