add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Accent (2000 release)

general info. full specifications. diagnostics. hints. tips. tricks
Hyundai Accent
Home
 
Hyundai
Accent
Instructions
Engine
Engines SOHC
Technical data
Toothed belt
Check toothed belt tension
Adjusting the tension of the toothed belt
Ribbed Belts
Engine Supports
The front cover and the oil pump
Air filter (ACL)
Cylinder head
Rocker
Hydraulic jacks of backlashes of valves
Replacing the valve seat
Replacing the valve guide
Valve
Camshaft
Cranks
Crankshaft
Flywheel
The piston pin
An exhaust manifold
Intake manifold and the air chamber
Cylinder block
Removing and installing engine and gearbox
Exhaust
Troubleshooting
Engines DOHC
Greasing system
Cooling
Control, reduced toxicity
Fuel system
Ignition system
Coupling
Transmission
Axes and power shafts
Suspension
Steering
Brakes
Body
Air
Electrical equipment
Appendix
Wiring
 


Hit Counter by Digits


print page printable version

Ribbed Belts



Withdrawal

PERFORMANCE ORDER
1. Loosen the bolts of the water pump pulley.
2. Loosen the nuts generator support.
3. Loosen the bolt of the generator and remove the V-ribbed belt.
4. Remove the bolts of the water pump pulley.

Torque:
The hinge bolt (A) securing the generator: 20-25 N ??? m
Bolt (B) fastening of the generator: 15-22 N ??? m
Bolt bracket generator: 20-28 N ??? m


Check

Check the following items and the presence of defects replace them.

PERFORMANCE ORDER
1. Check the surface of the V-ribbed belt for damage and cracks.
2. Check the surface of the V-ribbed belt in the absence of oil and grease.
3. Examine the surface of the V-ribbed belt on the absence of uneven wear.
4. Check the surface of the pulley for cracks or damage.

Setting

PERFORMANCE ORDER
1. Install the pump pulley and secure it with screws.
2. After installing the poly V-belt, adjust its tension.

Check and adjust the tension

PERFORMANCE ORDER
1. Check the V-belt and its location on the pulleys.

A warning

Check the location of the edges of the V-ribbed belt pulley groove.
If the V-ribbed belt makes unusual noise, check the belt for wear and damage, as well as working surfaces of pulleys.


2. The special device measure a tension of the alternator drive belt. In the absence of a special tool, check the belt tension, having pressed on it effort of 100 N (10 kg) in a place located on identical removal from pulleys and measure a belt deflection.

Alternator belt tension:
New belt: 65-75 kg
Second hand strap: 40 kg
Verification: 35-50 kg
Belt tension generator and the power steering pump:
New belt: 55-70 kg
Second hand strap: 38-48 kg
Belt tension generator and air conditioner:
New belt: 60-70 kg
Second hand strap: 32-40 kg
Verification: 25-50 kg

Reused belt is considered to be a belt, worked on the engine for more than 5 minutes.


Tension measurement special device type A

PERFORMANCE ORDER
When measuring the tension device wedge a belt must not touch the other components of the engine.

When measuring the tension device wedge a belt must not touch the other components of the engine.

PERFORMANCE ORDER
1. When measuring ensure that the key turned in the direction of re-installation of the arrow, the arrow to set the device to its original state.
2. After removing the unit from the belt needle still will indicate the belt tension.

A warning

It is not recommended to adjust the tension of the belt by hand, as this regulation does not provide sufficient accuracy and the belt can slip on the pulleys. Always use a special device.
Check that the tension of the belt corresponds to the desired value.
Check the belt tension after tightening the hinge screws and bolts of the generator.






« previos page
Adjusting the tension of the toothed belt
next page »
Engine Supports

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.