 printable version
Seats
Manual adjustment of the position of the front seats
The adjustment is recommended as follows:
1. The longitudinal movement of the seat
Lift the handle and set the seat to a position in which it is convenient achieved accelerator and brake pedals.
2. Tilt the seat cushion
Rotate the handle forward or backward to achieve a position that provides an easy support for thighs.
3. Seat height
Pull the lever - lifting seat
Click on the lever - lowering the seat cushion
4. Tilt back
Rotate the handle until the seat back is not set in the desired position. For reasons of safety it is recommended in an upward position.
 | When the position unload the back. |
The height of the head restraint  | 5 Exemption headrest |
Setting up: pull the head restraint upwards.
Installation below: Press the release button (5) and lower the headrest pushing it from the top.
Install the head restraint so that his head rested on him at about eye level. Tilt the head restraint adjust manually. Pull or press the front headrests.
Electrically adjustable front seats
The key is in the ignition switch, turn to position 1 or 2.
When you open the driver's door of the driver seat adjustment can be made with the key inserted.
Adjusting the position of the front passenger seat can also be carried out at one door open. | If adjusting the position of the seat is made of the provisions for lying or positioned far from the position, be careful that the rear cosmetic mirrors were closed. |
Switches in the front doors
Seat adjustment is possible if the key is in the ignition switch is turned to the position 1 or 2 or open the corresponding door.  | |
The main adjustment is recommended as follows:
1. Seat height
Moves switch back to the direction of the arrow until it reaches its highest position, while maintaining sufficient free space overhead.
2. The longitudinal movement of the seat
The switch is in the direction of the arrow until, until it reaches a position which is reached at which the accelerator and brake pedals.
3. The slope of the seat cushion
Switch is in the front in the direction of the arrow to reach the position that provides an easy support for thighs.
4. Tilt back
The switch is in the direction of the arrow until, until a desired position of the seat back. For safety reasons, we recommend an almost vertical position. The steering wheel is set so that the hand lying on the steering wheel, was slightly bent.
5. The height of the head restraint
The height of head restraints installed when adjusting the switch so that the back of his head found an emphasis on the head restraint at about eye level.  | |
Tilt the head restraint adjust manually. Drag or click on the headrest in front. Releasing and fixing the front seat backs
Function facilitate landing If the seat is in the back third of the range of seat adjustment, for the ease of planting, in addition to the back leans forward and the seat cushion. On models with electric seat adjustment system, the additional electric drive lowering the headrest.
Folding the seat backrest forward:
Turn the handle forward and then fold the backrest forward.
Note for models with manual seat adjustment:
Fold the backrest forward to the seat, if necessary, lower the headrest.
Folding the seat backrest back:
Fold the backrest back and click on it to fix the situation in motion.
On models with manual seat adjustment flip back to the seat back, if necessary, lower the headrest.
Seat heating
The key is in the ignition switch, turn to position 1 or 2. | When you turn on too many accessories or insufficient battery charge seat heater may disconnect. In this case, one or both of the flashing indicator lamp. |
When you restore a sufficient voltage seat heater is turned on automatically.
The switch in the center console. 1. Button "normal heating mode"
2. Button "maximum heating mode" Press (1):
The red LED on the control button.
Normal heating mode.
After about 30 minutes, the seat heater is automatically switched off.
Press (2):
Light up the two red LED on the control button. The maximum heating.
After about 5 minutes, automatically switches to the normal heating mode.
Button (1) or (2) Press again:
None of the control LED is off.
Seat heater is turned off.
Rear head restraints
If the rear seats are occupied, move only with the mounted head restraints. This reduces the risk of injury to passengers in the back seat in a crash. 1 Key
Folding:
Press (1). Headrest reclines.
Setting up:
Tilt the head up by hand (arrow) until it locks.
Incline:
Headrests can be fixed in 2 positions. To do this, press (1) and set the head to the desired position. Headrest set as close as possible to the head.
The height of the head restraint 2 When the headrest
The headrests can be adjusted in height.
Installation above:
Pull the head restraint upwards. If the head restraint has been pushed to the end, press the release button (2).
Installation below:
Press release (2) and lower the headrest pushing it from the top.
Removal and installation of headrests | To facilitate the installation and removal of the head restraints slightly tilt the seat back.
The front seats are manually adjustable, rear bench seat |
Removing the head restraint:
Raise the head restraint up until it stops. Press the release button (1) and pull the headrest.
Installing the head restraint:
Headrest set so that the retainer plug located on the left in the direction of travel.
Headrest press down until it locks. Electrically adjustable front seats Removing the head restraint
The switch (1), slide up and hold this position for as long as the headrest pops through. Pull the head restraint.
Installing headrest
Switch (1) press up for about 5 seconds.
Headrest set so that the retainer plug located on the left in the direction of travel.
Headrest press down until it locks.
With the switch lower the headrest down to the stop and lift up the top until it stops.
| 
