Signal & Lighting

1. Disconnect the negative wire from the battery.
2. On models of utilities (Van) (Utility) and Mini truck (Cab Chassis) release the retaining clips and remove from the car grille.
3. Disconnect the unit lights wiring.
4. By keeping the lens unit, fastening screws give her a ring holder. Remove the ring holder and the lens unit from the car.

1. Disconnect the negative wire from the battery.
2. Disconnect the electrical connector head lights.
3. Remove the back of the headlight rubber protective cover, press the bulb holder and turn it counterclockwise. Remove the bulb from the headlight unit (headlight unit components are shown in an accompanying illustration).

1 - Protective Case 2 - Holder 3 - Lamp 4 - block headlamp 5 - ring 6 - screws

Try not to touch the glass of the bulb with bare fingers. Fat deposits shorten the life of the lamp. Accidentally left stains can be removed with the use of methanol, after which the flask should be dried by wiping it with a clean cloth or a piece of cotton fabric.

4. Install the new bulb in the socket. Check the installation. Also, check for correct installation of the holder and a protective cover.

1. Make sure the correct tire inflation pressure and completeness of filling the fuel tank. Park the unloaded vehicle on a level surface. On the driver's seat plant assistant.
2. If you have a special device to adjust the direction of beam headlights, read the enclosed instructions.
3. When using a control panel the car should be parked five meters away (distance A in the illustration - see. Below) and perpendicular to the plane of the board.

The control panel can be used flat wall, which should cause corresponding chalk markings.

4. Mel performed on board a horizontal line marking, passing through the axial plane of the headlights of the car and at the height of their centers (see para. Accompanying illustration).

1 - central line 2 - Control panel 3 - car 4 - spot beam 5 - spot beam 6 - correct positioning of light spots

5. Draw two vertical lines corresponding to the vertical center lines of the headlights of the car.
6. Turn on the dipped headlights.

Screw the stop adjustment screws, located at the top and sides of the headlight units (see. Accompanying illustration), and then release them, achieving the desired direction of the rays of headlights.

8. Adjust the direction of the beam of the headlights in accordance with the requirements adopted in a particular region of the SDA. In general, such placement Get beam spots when the line is horizontal slice spot is on the horizontal line marking on a board, or a little below it. The raised portion of spots should be on the vertical line marking or to the right of it.

1. Give fixing screws and remove the assembly combination lamp.

Turn a cartridge counter-clockwise and remove it from the lamp assembly (removal of the front parking lamps fire car models of Hardtop and the Versatile shown in the accompanying illustration).

3. Grasping the flask, gently pull the bulb out of its socket.
4. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
5. Install the assembly combined lantern on the car.

1. Give fixing screws and remove the lens combination lamp with a sealant.
2. Click on the lamp, turn it counter-clockwise and remove the cartridge.
3. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
4. Replace the lens flashlight, following the installation of rubber seal.

1. Give fixing screws and remove the assembly combination lamp.

Turn a cartridge counter-clockwise and remove it from the lamp assembly (removal of the front turn signal lamps car models of Hardtop and the Versatile shown in the accompanying illustration).

3. Click on the lamp, turn it counter-clockwise and remove the cartridge.
4. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
5. Install the assembly combined lantern on the car.

1. Give fixing screws and remove the lens combination lamp with a sealant.
2. Click on the lamp, turn it counter-clockwise and remove the cartridge.
3. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
4. Replace the lens flashlight, following the installation of rubber seal.

Installation is in the reverse order.

1. Pre-check the cartridge for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
2. Set the pointer to build the car.

1. Give fixing screws and remove the lens with a sealant.
2. Click on the lamp, turn it counter-clockwise and remove the cartridge.
3. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
4. Replace the lens flashlight, following the installation of rubber seal.

1. Give fixing screws and remove the lamp assembly of the car.

Turn a cartridge counter-clockwise and remove it from the lamp assembly (removal of one of the rear combination lamp bulbs car models of Hardtop and the Versatile shown in the accompanying illustration).

3. Click on the lamp, turn it counter-clockwise and remove the cartridge.
4. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
5. Install the assembly combined lantern on the car.

1. Give krkpezhnye screws and remove the lens combination lamp with a sealant.
2. Click on the lamp, turn it counter-clockwise and remove the cartridge.
3. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
4. Replace the lens flashlight, following the installation of rubber seal.

1. Give fixing screws and remove the lamp assembly of the car.

Click on the lamp, turn it counter-clockwise and remove the cartridge (see. Accompanying illustration).

3. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
4. Install the assembly combined lantern on the car.

1. Give fixing screws and remove the lamp assembly of the car.

Click on the lamp, turn it counter-clockwise and remove the cartridge (see. Accompanying illustration).

3. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
4. Install the assembly combined lantern on the car.

1. Use a screwdriver to remove the cover with finishing assembly of a stoplight.
2. Turn the bulb holder anticlockwise and remove it from the lens.
3. Pull and remove the bulb from the socket.
4. Make sure there is no corrosion of the cartridge and insert a new bulb.
5. Install the lamp cartridge with the lens. Turn the cartridge clockwise to lock it into the lens.
6. Replace the base assembly cover finishing. Replace and tighten the screw.

1. Give fixing screws and remove the lamp lens with the seal.

Click on the lamp, turn it counter-clockwise and remove the cartridge (see. Accompanying illustration - shows light hardtop models and Touring).

3. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion, and the lamp itself for compliance with the requirements of the rated power and voltage supply (see. Table sizes and adjustments in the end of this manual).
4. Install the assembly combined lantern on the car.

1. Having hooked a small screwdriver, carefully remove the bowl from the body of the lamp.
2. Grasping the flask, gently pull the bulb out of its socket.
3. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion. Make sure of reliability of fastening of the lamp, which guarantees the quality of the electrical contact.
4. Replace the ceiling lamp.

1. On models equipped with a lamp square-shaped, gently prying with a small screwdriver, remove the bowl from the body of the lamp.
2. On models with a round lamp for removal turn the bowl counterclockwise.

Carefully remove the bulb festoon type of terminal clamp holder (see. Accompanying illustration).

4. Install the lamp in a cartridge, the cartridge after checking for signs of corrosion. Make sure of reliability of fastening the lamp holder clamps, guaranteeing the quality of the electrical contact.
5. Replace the ceiling lamp.

1. Gently prying with a screwdriver, remove the bowl from the lamp assembly.

Click on the lamp, turn it counter-clockwise and remove it from the holder (see. Accompanying illustration).

3. Installation is in the reverse order. Check for corrosion cartridge and install a new lamp, removed at the appropriate operating parameters (see. Table sizes and adjustments in the end of this manual).
4. Replace the dome.