add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Accent (2000 release)

general info. full specifications. diagnostics. hints. tips. tricks
Hyundai Accent
Home
 
Hyundai
Accent
Instructions
Engine
Engines SOHC
Engines DOHC
Technical data
Compression Test
Toothed belt
Ribbed Belts
Engine Supports
Front Cover
Air filter (ACL)
Cylinder head
Camshafts
Replacing the valve seat
Replacing the valve guide
Valve
Cranks
Crankshaft
Flywheel
Piston
An exhaust manifold
Intake manifold and the air chamber
Cylinder block
Removing and installing engine and gearbox
Exhaust
Troubleshooting
Greasing system
Cooling
Control, reduced toxicity
Fuel system
Ignition system
Coupling
Transmission
Axes and power shafts
Suspension
Steering
Brakes
Body
Air
Electrical equipment
Appendix
Wiring
 


Hit Counter by Digits


print page printable version

Piston



Withdrawal

PERFORMANCE ORDER
1. For the disassembly and reassembly of the piston and the connecting rod is necessary to use special tools 09234-33001.
2. Set the universal support in the nip between the connecting rod and the piston.
3. Insert the removal tool through the hole in the arch of the clamp.

A warning

Insert the clamp with piston rod puller and a press ram.


4. A stripper squeeze out the piston pin from the piston.

Check

The piston and the piston pin

PERFORMANCE ORDER
1. Check the outer surface of the piston for damage, develop or uneven wear. If necessary, replace the piston.
2. Check each piston ring for damage and uneven wear. If necessary, replace the piston rings.
3. Check the piston pin by inserting it into the hole of the piston. The piston pin must be a smooth entrance into the piston by pressing it by hand (at room temperature).

Piston rings

PERFORMANCE ORDER
1. Insert the new piston ring in the groove of the piston and probe measure the clearance between the piston ring and the wall of the groove. If the clearance exceeds the limit, replace the piston.

The gap between the piston ring and the groove in the piston:
The first compression ring: 0,04-0,085 mm
The second compression ring: 0,04-0,085 mm
Maximum permissible backlash: 0,1 mm

2. Measure the end gap of the piston rings, piston ring is manually inserted into the engine cylinder. Piston crown push the piston ring into the bottom of the cylinder. Feeler gauge, measure the end gap of the piston ring.

The gap piston ring:
The first compression ring: 0.15-0.30 mm
The second compression ring: 0.20-0.40 mm
Scraper ring: 0,20-0,70 mm
Maximum permissible backlash: 1,0 mm


Setting

PERFORMANCE ORDER
1. Install the spacer.
2. Install the upper side rail. To install the side rail, first place one end of the side guide wall between the piston ring groove and the spacer, click on it and then clicking on the perimeter, install it in the groove of the piston.

A warning

Do not use pliers for a release of piston rings when installing side rail.


3. Likewise, set the low side guide.
4. pliers for a release of piston rings, set the compression ring ?��2.
5. pliers for a release of piston rings, set the compression ring ?��1.
6. Apply a thin coat of engine oil to the piston and piston rings.
7. Place the piston rings, as shown in the figure.
8. The special adaptation compress piston rings on the piston.
9. Install the guide pins through the piston to the connecting rod and piston pin set on the other side of the piston.

A warning

The guide pins define the position of the connecting rod in the piston. After you install the piston, connecting rod, piston pin, and for adjustment of the piston pin in the insertion guide pins also determine their position in the clip.


10. Install the piston assembly to the clamp, and the guide pin support rod in the piston pin.
11. Check that the mutual position of the piston and connecting rod and turn the knurled nut, attach numbered sleeve on the shaft.
12. Insert the shaft through the hole in the arch of the clip. Push piston pin to connecting rod, while the sleeve on the shaft engages with the upper part of the clamp arch, wherein the guide pin has to fall from the piston.

A warning

The force pressing the piston pin must not exceed 22,500 N.


Joining depth: 0.3-0.5 mm





« previos page
Flywheel
next page »
An exhaust manifold

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.