add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Jeep Grand Cherokee (from 1993 to 1999, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks
Jeep Grand Cherokee
Home
 
Jeep
Grand Cherokee
Introduction
Adjustment and routine maintenance
The straight six-cylinder engine
The V8 engine
Procedure of the general and engine major repairs
Systems of cooling, heating and air conditioning
The power supply system and exhaust
The system of electric motor
Systems of decrease in toxicity of the fulfilled gases and engine management
Manual box of a gear change
Automatic Transmission
Transfer Case
Clutch and transmission line
Brakes
Suspension and steering
Body
The system of on-board electrical equipment
general information
Troubleshooting electrical chassis - general information
Safety locks - the general information
Fuse - General Information
Circuit breakers (thermal relays) - the general information
Relays - General Information
Check and replacement of the breaker of indexes of turn / alarm
Check of serviceability of functioning and replacement universal stalk
Check and replace the ignition switch / lock cylinder
Check of serviceability of functioning of the switch heating glass tailgate
Check and repair the heater glass tailgate
Replacing bulbs headlights
Tilt the head block headlights
Removal and installation of towers head block headlights
Replacing bulbs
Removal and installation of switches headlights and tailgate window wiper
Removal and installation of radio and speakers
Removal and installation of the antenna
Check functioning and replacement of the wiper motor
Removal and installation of the instrument cluster
Check of functioning and replacement horn
Description of the principle of operation and diagnosis of the speed control (Tempostat)
Operation principle and diagnostics of electric lowering-raising glasses
The principle of operation and test the central locking system and open the door without a key
Principle of operation and check of serviceability of electric repositioning seats
Principle of operation and check of serviceability of electric rearview form
Airbag - general information
Wiring diagrams - General information
Location and Function relays and fuses
Controls and operation receptions
 


Hit Counter by Digits


print page printable version

Check and repair the heater glass tailgate



Heater glass tailgate is a series of horizontal elements glued onto the glass surface on its inner side.

Small gaps elements can be eliminated without removing the glass.

Check

PERFORMANCE ORDER

  1. Turn on the ignition and the heater glass tailgate.
  2. Ground the negative lead of the voltmeter to the terminal A, connect the positive terminal B.

Testing point heater glass tailgate.

  1. Voltmeter should be in the range between 10 and 15 V. The lower voltage to a violation of the quality of the grounding.
  2. Connect the voltmeter negative lead to a good ground point - reading should not change.
  3. Connect the negative cable to the terminal A, then the touch probe turns positive wire to the middle point of each of the grating lines of the heater.
  4. Readings shall be each time about 6 V. The zero voltmeter reading indicates a continuity between the midpoint C and terminal B.
  5. Display 10 - 14 indicates a continuity between the midpoint C and the terminal A. Set the probe to the side of the cliff; after crossing the last reading will change.

Repairs

PERFORMANCE ORDER

  1. In order to restore the continuity of lattice elements is recommended to use special repair kits such as MOPAR ?�� 4267922 (or equivalent). The kit contains a plastic Conductive epoxy compound.
  2. Before the start of the recovery, turn off the heater element let it cool for a few minutes.
  3. Lightly rub the affected area with a thin stiff hair, then wipe it with alcohol.
  4. Apply masking tape on both sides of the damaged section parallel to the line item.
  1. To restore the damaged section of the horizontal heater element lattice paste on both sides of a strip of adhesive tape.
  1. Thoroughly knead the compound in accordance with the instructions attached to the kit.
  2. Apply the compound into the lumen between the strips of tape on the damaged section of the element, blocking its healthy edge approximately 20 mm.
  3. Allow the compound to stand for 24 hours, then you can remove the masking tape and try heater.




« previos page
Check of serviceability of functioning of the switch heating glass tailgate
next page »
Replacing bulbs headlights

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.