add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Jeep Grand Cherokee (from 1993 to 1999, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks
Jeep Grand Cherokee
Home
 
Jeep
Grand Cherokee
Introduction
Adjustment and routine maintenance
The straight six-cylinder engine
The V8 engine
Procedure of the general and engine major repairs
Systems of cooling, heating and air conditioning
The power supply system and exhaust
The system of electric motor
Systems of decrease in toxicity of the fulfilled gases and engine management
Manual box of a gear change
Automatic Transmission
Transfer Case
Clutch and transmission line
Brakes
Suspension and steering
Body
The system of on-board electrical equipment
general information
Troubleshooting electrical chassis - general information
Safety locks - the general information
Fuse - General Information
Circuit breakers (thermal relays) - the general information
Relays - General Information
Check and replacement of the breaker of indexes of turn / alarm
Check of serviceability of functioning and replacement universal stalk
Check and replace the ignition switch / lock cylinder
Check of serviceability of functioning of the switch heating glass tailgate
Check and repair the heater glass tailgate
Replacing bulbs headlights
Tilt the head block headlights
Removal and installation of towers head block headlights
Replacing bulbs
Removal and installation of switches headlights and tailgate window wiper
Removal and installation of radio and speakers
Removal and installation of the antenna
Check functioning and replacement of the wiper motor
Removal and installation of the instrument cluster
Check of functioning and replacement horn
Description of the principle of operation and diagnosis of the speed control (Tempostat)
Operation principle and diagnostics of electric lowering-raising glasses
The principle of operation and test the central locking system and open the door without a key
Principle of operation and check of serviceability of electric repositioning seats
Principle of operation and check of serviceability of electric rearview form
Airbag - general information
Wiring diagrams - General information
Location and Function relays and fuses
Controls and operation receptions
 


Hit Counter by Digits


print page printable version

Troubleshooting electrical chassis - general information



The structure of a typical electric circuit may include an electrical component, a variety of switches, relays, motors, fuses, fuses or circuit breakers that are relevant to this component, as well as wiring and electrical connectors that serve to connect a component with battery and weight of the chassis. To facilitate the task of troubleshooting electrical circuits in Section Electric schemes - general information.

Before starting to work on troubleshooting any of the electrical circuits, read the corresponding application schema, so that as clearly as possible to imagine its functional purpose. Narrowing the range of troubleshooting is usually done by a gradual identification and elimination of well-functioning components of the same circuit. With the simultaneous failure of several components or circuits most likely cause of failure is a blown fuse or a violation of the relevant ground (various contours in many cases may be closed by one fuse or earth terminal).

Electrical failure is often explained by simple reasons, such as corrosion of the terminals, the failure of fuse burning fuse or defective relay switch. Perform a visual check of the status of all fuses, wiring and electrical connectors circuit before embarking on a more specific check of serviceability of its components.

In the case of applications for troubleshooting diagnostic tools, plan carefully in accordance with the wiring diagrams in any point of the circuit and the sequence in which the device must be connected with the aim of identifying the most effective defect.

The main diagnostic devices include electrical circuits tester or voltmeter (can also be used in the warning lamp 12 with a set of connecting wires), an indicator of the continuity of the segment circuit (probe), which includes a light bulb, its own power supply and a set of connecting wires. Furthermore, always be a set of wires in a vehicle to start the engine from the auxiliary source equipped with alligator clips and preferably interrupter circuit which can be used for bridging and connecting various electrical components in diagnostic circuit. As mentioned above, before proceeding to the verification of the circuit using the diagnostic equipment, determine the schemes of his place of connection.

Checking voltage

Check availability of the voltage produced in the event of malfunction of the circuit. Connect one of the wires in the electrical circuits of the tester or to the negative pole of the battery or to a well-grounded at the chassis of the car. Another wire tester connected to the terminal of an electric socket circuit, preferably next to the battery or fuse. If the warning lamp on the tester lights up, the voltage on this segment of the chain takes place, confirming serviceability of the circuit between the terminal and the battery. Continuing to operate in a similar manner, explore the rest of the circuit. Detection of absence of voltage indicates a fault between a given point of the circuit and the last of the previously tested (where the voltage is present). In most cases, the cause of failure is a weakening of the electrical connections and the violation of the quality of contacts.

Remember that power some of the circuits electrical chassis is supplied only in ignition switch positions ACC (parking) or RUN (movement).

The search for short circuit

One method of searching is to extract short-circuit fuse and connection instead lamp or voltmeter probe. The voltage in the circuit should be absent. Pulled wiring, watching the lamp-sampler. If the lamp flashes, somewhere in the harness has a short to ground, possibly caused by rubbing the wire insulation. A similar test can be performed for each of the circuit components, including circuit breakers.

Check of earthing

This test is performed to determine the reliability of the ground component. Disconnect the battery and connect one wire-equipped self-powered lamp probe grounded to a known good point. Another lamp wire to connect the wiring or the terminal under test. If the lamp lights up, grounding in the order (and vice versa).

Check for conductivity

Checks are made to identify the continuity circuit After a power circuit, check it with a lamp-sampler equipped with autonomous battery. Connect the probe to both ends of the circuit (or "force" the end of the (+) and is well grounded at the chassis) if the test lamp illuminates, there is no break in the circuit. Disclaimer turn on the lamp indicates a violation of the chain of continuity. Similarly, the same way you can check the power switch and connecting the probe to the terminals. While translating the switch in the "On" indicator lamp should light up-sampler.

Localization cliff

In the diagnosis of a suspect for an open circuit to visually detect the cause of the problem is rather difficult, as inspection terminals for corrosion or violation of the quality of their contacts is difficult because of limited access to them (normally closed terminal connector housing). Sudden twitching body connector on the sensor or its wiring harness in many cases leads to the restoration of conductivity. Keep this in mind when trying to localize the causes of failure of a suspect for an open circuit. Unstable occurring failures can be caused by oxidation of terminal or violation of the quality of contacts.

Troubleshooting of electrical circuits is not an intractable problem is with a clear idea that the current supplied to all electrical loads (lamp, motor, etc.) from the battery through the wires through switches, relays, fuses, fusible links, and then It returns to the battery via the vehicle weight. Any problems associated with electrical failure may have its only cause them to cease supplying electric current from a battery or returning it to it.





« previos page
general information
next page »
Safety locks - the general information

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.