REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Kia Sephia / Shuma (1995 release)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Kia
	Sephia / Shuma
		Maintenance
		Engine
		Greasing system
		Cooling
		The power supply system and release
		Fuel system
		Ignition system
		Coupling
		Manual transmission
		Automatic Transmission
		Axes and power shafts
		Steering
		Wheels and tires
		Brakes
		Suspension
		Body
			Technical data
			Front bumper
			Rear bumper
			The front door
			Conformal door seal
			Door hinges and door lock strike plate
			Door lock
			Inner Door handle
			The outer door handle
			Cylinder door lock
			Window switches
			Power windows
			Glass doors
			Backdoor
			Spotlight
			High level brake light
			The rear combination lamp
			Ceiling
			Hood
			Sound signal
			Device combination
			Repair of the instrument cluster
			Replacing bulbs dash
			Printed circuit board
			The top decorative overlay of the panel of devices
			Switches
			The central panel
			Cover center console
			The center console
			Dimmer dashboard
			The left and right lattices of a heater of a windscreen
			The left and right lateral lattices of a heater
			Ducts heating and ventilation systems
			Floor ducts
			Glovebox
			A cable of opening the bonnet
			Handle opening the bonnet
			Dashboard
			The control panel heating and ventilation
			Door mirror
			Replacing the glass door mirror
			The front seats
			Upholstery front seatback
			The upholstery of the front seat
			The leaning back hinge of a forward seat
			Rear seat
			Seat belts
			Lock the front seat
			Front shoulder belt
			Rear seat belts
			Bracket rear seat belt
			Shoulder rear seat belt
			The top furnish of a forward rack
			The bottom furnish of the central rack
			The top furnish of the central rack
			Finish the back of the rack
			Finishing stand legs
			Front side door trim
			Rear door trim
			The trunk lid
			The hinge lid
			Windshield washer hose
			Engine windshield washer
			Wiper Arm
			Sprayers
			Replacing the wiper blades
			Traction wiper
			Wiper Motor
			Distances between body points
		The air conditioning system
		Electrical equipment

printable version

Cylinder door lock

Withdrawal

PERFORMANCE ORDER

1. Disconnect the negative battery terminal.
2. Remove the door trim.
	3. Remove one screw securing the bracket of the internal handle of opening of the door.
4. Remove an arm of the internal handle of the door opening.
	5. Remove the door from the speaker in the following order: a. Remove the three screws that secure the speaker to the door; b. Disconnect the wiring harness from the door frame; c. remove the speaker and disconnect connectors.
	6. Remove pylevlagozaschitnuyu film, gradually separating it from the door frame.
7. Disconnect draft of the door lock on the outside door handle.
8. Remove the cylinder rod lock the door from the outside door handle.
	9. Remove the two screws on the outside door handle.
10. Remove the outside door handle.
	11. Remove the lock cylinder from outside door handle.

Setting

PERFORMANCE ORDER

1. Install the lock cylinder in the outside door handle.
2. Attach the lock cylinder on the outside door handle.
3. Install the outside door handle.
	4. Replace the two screws on the outside door handle. Torque: 9-13 N ??? m
5. Connect the door lock cylinder rod to the outside door handle.
6. Connect traction lock the door to the outer door handle.
	7. Replace the door pylevlagozaschitnuyu film in the following order: a. secure pylevlagozaschitnuyu film on the door; b. output wiring harness electrical connector door; c. output thrust of the internal handle of opening of the door lock pylevlagozaschitnoy film.
	8. Set the speaker and secure it with three screws.
9. Establish an arm of the handle and secure it with one screw.
10. Install the door trim.
11. Connect the cable to the negative terminal of the battery.

« previos page
The outer door handle

next page »
Window switches