add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Kia Sephia / Shuma (1995 release)

general info. full specifications. diagnostics. hints. tips. tricks
Kia Sephia / Shuma
Home
 
Kia
Sephia / Shuma
Maintenance
Engine
Greasing system
Cooling
The power supply system and release
Fuel system
Ignition system
Coupling
Manual transmission
Automatic Transmission
Axes and power shafts
Steering
Wheels and tires
Brakes
Suspension
Body
Technical data
Front bumper
Rear bumper
The front door
Conformal door seal
Door hinges and door lock strike plate
Door lock
Inner Door handle
The outer door handle
Cylinder door lock
Window switches
Power windows
Glass doors
Backdoor
Spotlight
High level brake light
The rear combination lamp
Ceiling
Hood
Sound signal
Device combination
Repair of the instrument cluster
Replacing bulbs dash
Printed circuit board
The top decorative overlay of the panel of devices
Switches
The central panel
Cover center console
The center console
Dimmer dashboard
The left and right lattices of a heater of a windscreen
The left and right lateral lattices of a heater
Ducts heating and ventilation systems
Floor ducts
Glovebox
A cable of opening the bonnet
Handle opening the bonnet
Dashboard
The control panel heating and ventilation
Door mirror
Replacing the glass door mirror
The front seats
Upholstery front seatback
The upholstery of the front seat
The leaning back hinge of a forward seat
Rear seat
Seat belts
Lock the front seat
Front shoulder belt
Rear seat belts
Bracket rear seat belt
Shoulder rear seat belt
The top furnish of a forward rack
The bottom furnish of the central rack
The top furnish of the central rack
Finish the back of the rack
Finishing stand legs
Front side door trim
Rear door trim
The trunk lid
The hinge lid
Windshield washer hose
Engine windshield washer
Wiper Arm
Sprayers
Replacing the wiper blades
Traction wiper
Wiper Motor
Distances between body points
The air conditioning system
Electrical equipment
 


Hit Counter by Digits


print page printable version

Glass doors



Withdrawal

PERFORMANCE ORDER
1. Disconnect the negative battery terminal.
2. Remove the door trim.
3. Remove one screw securing the bracket of the internal handle of opening of the door.
4. Remove an arm of the internal handle of the door opening.
5. Remove the door from the speaker in the following order:
a. Remove the three screws that secure the speaker to the door;
b. Disconnect the wiring harness from the door frame;
c. remove the speaker and disconnect connectors.
6. Remove pylevlagozaschitnuyu film, gradually separating it from the door frame.
7. Remove the glass in the following order:
a. reconnect the power window control switch;
b. connect the wire to the negative terminal of the battery;
c. Switch on the ignition and move glass in a half-open position;
d. switch off the ignition;
e. disconnect the wire from the negative terminal of the battery;
f. Remove the two screws on the glass to the window;
g. tilting and lifting the back, remove the glass from the outside of the door.

Setting

PERFORMANCE ORDER
1. Loosen one bolt of glass.
2. Place the glass in the following order:
a. Insert the outside of the door at first a forward part of the glass, and then, turning and lowering, set the glass on the door and place it on the bracket window;
b. screw, but do not tighten definitively bolts of glass;
c. reconnect the power window control switch;
d. Switch on the ignition and move the window up and down to activate the window control;
e. if necessary, adjust the position of the glass;
f. switch off the ignition;
g. disconnect the wire from the negative terminal of the battery;
h. tighten the two screws on the glass to the window;

Tightening torque: 2.3 N ??? m
i. tighten a bolt of glass;

Torque: 9-13 N ??? m
3. Replace the door pylevlagozaschitnuyu film in the following order:
a. secure pylevlagozaschitnuyu film on the door;
b. output wiring harness electrical connector door;
c. output thrust of the internal handle of opening of the door lock pylevlagozaschitnoy film.
4. Install the speaker and secure it with three screws.
5. Install the bracket handle and secure it with one screw.
6. Install the door trim.




« previos page
Power windows
next page »
Backdoor

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.