REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Hyundai Elantra (from 2000 to 2004, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Hyundai
	Elantra
		Gasoline engines 1.6, 1.8 and 2.0 liters
		The diesel engine of 2.0 liters
		Greasing system
		Cooling
		Fuel system
		Control systems and emission control
		Ignition system
		The system of preliminary heating of the diesel engine
		Coupling
		Manual transmission
		Automatic Transmission
			Technical data
			Check the fluid level in automatic transmission
			Substitution fluid in an automatic transmission
			Check conduction switch the transmission range (F4A42)
			Switch the transmission range and adjustment of the control cable (F4A42)
			Check the operation of the selector lever (A4AF3)
			Adjustment of the switch indicate the position of the selector lever (A4AF3)
			Component testing of an automatic transmission (F4A42)
			Testing of teamwork of an automatic transmission and the engine for the motionless car (F4A42)
			Check the transmission fluid pressure (F4A42)
			Check the transmission fluid pressure (A4AF3)
			The diagnostic function
			Diagnostic codes
			Adjustment of an axial backlash reaction brake (F4A42)
			Adjusting the axial clearance of the brake of the second transmission (F4A42)
			Adjusting the axial clearance of the brake transmission and low reverse gear (F4A42)
			Adjusting the axial clearance of the sun gear downshift (F4A42)
			Adjusting the preload of the differential (F4A42)
			Elements of hydraulic control system
			Identification of bearing automatic transmission F4A42
			The control lamp fault (MIL)
			Identification of bearing automatic transmission F4A43
			Adjusting the servo compulsory inclusion downshift (A4AF3)
			Adjust the line pressure (A4AF3)
			Replacement of an oil sealing ring of a power shaft
			Removing and installing transmission F4A42
			Removing and installing transmission A4AF3
			Control automatic transmission
			Installing the locking device
			Installing a locking key
		Drive shafts, front and rear axles
		Suspension
		Steering
		Brakes
		Body
		The air conditioning system
		Electrical equipment
		Electrical diagrams

printable version

Check the transmission fluid pressure (F4A42)

Check the transmission fluid pressure is performed in order to determine the condition of hydraulic components and whether there are leaks.

PERFORMANCE ORDER

Start up the engine before warming up of a transmission to temperature 80-100 ?° C.
Lift the front side of the car so that the drive wheels can rotate freely.

Connect a pressure gauge with a special adapter for each nipple pressure test.

Measure the pressure of the transmission fluid at various positions of the gear lever and the speed of the crankshaft of the engine in the table.

If the pressure does not correspond to the desired value, check and repair the transmission elements.

Automatic Transmission F4A42

condition			Standard transmission fluid pressure, kPa
Provisions selector	Selector lever position	Engine ^speed, min -1	Reduced pressure (UD)	Rear traction (REV)	Pressure overdrive clutch (OD)
R	-	2500	-	-	-
R	ZK	2500	-	1,270-1,770	-
N	Neutral.	-	-	-	-
D	1st per.	2500	1,010-1,050	-	-
	2nd lane.	2500	1,010-1,050	-	-
	3rd per.	2500	780-800	-	780-880
	4th lane.	2500	-	-	780-880

Automatic Transmission F4A42 (continued)

Standard transmission fluid pressure, kPa
Brakes lower gears and ZK (LR)	Brakes 2 assists (2ND)	Clutch Pressure regulator (DA)	Pressure regulator damper clutch (DR)
260-340	-	-	220-360
1,270-1,770	-	-	500-700
260-340	-	-	220-360
1,010-1,050	-	-	500-700
-	1,010-1,050	-	500-700
-	-	More than 750	450-650
-	780-880	More than 750	450-650

Analysis of the test pressure of the transmission fluid (F4A42)

Symptom	possible cause
All hydraulic high pressure	Incorrectly adjusted control cable transmission
All hydraulic high pressure	Pressure control valve defective
All hydraulic pressure low	Incorrectly adjusted control cable transmission
	Faulty oil pump
	Dirty oil filter internal
	Blocked oil cooler
	Pressure control valve defective
	Faulty relief valve
	Improperly installed valve body
Hydraulic pressure is abnormally only at position selector ?«R?»	Pressure control valve defective
	Opening is blocked
	Improperly installed valve body
Hydraulic pressure is abnormally only at position selector "3" or "4"	Pressure control valve defective
	Opening is blocked
	Improperly installed valve body
	Defective solenoid valve overdrive
	Faulty pressure control valve overdrive
	Faulty valve switch
Hydraulic pressure is abnormally only downshift	Damaged oil seal K
	Damaged oil seal L
	Damaged oil seal M
	possible cause
	Defective solenoid valve downshift
	Faulty pressure control valve downshift
	Damaged ball control
	Opening is blocked
	Improperly installed valve body
Hydraulic pressure is abnormally only in reverse gear clutch	A damaged oil seal
	Damaged oil seal B
	Damaged oil seal C
	Opening is blocked
	Improperly installed valve body
Hydraulic pressure is abnormally only in overdrive	Damaged oil seal D
	Damaged oil seal E
	Damaged oil seal F
	Defective solenoid valve overdrive
	Faulty pressure control valve overdrive
	Damaged ball control
	Opening is blocked
	Improperly installed valve body
Hydraulic pressure is abnormally only in low gears and reverse gear	Damaged oil seal I
	Damaged oil seal J
	Defective solenoid valve low gears and reverse gear
	Faulty low pressure regulating valve gear and reverse gear
	Faulty valve switch
	Faulty relief valve A
	Damaged ball control
	Opening is blocked
	Improperly installed valve body
Abnormally only secondary hydraulic pressure	Damaged oil seal G
	Damaged oil seal H
	Damaged oil seal O
	Defective solenoid valve secondary
	Faulty secondary pressure control valve
	Faulty safety valve
	Opening is blocked
	Improperly installed valve body
Abnormally only the hydraulic pressure clutch reverse gear	Damaged oil cooler
	Damaged oil seal N
	Faulty solenoid clutch control damper
	Faulty damper clutch control valve
	Faulty pressure control valve torque converter
	Opening is blocked
Pressure is applied not to a functioning element	Improperly installed valve body
	Incorrectly adjusted control cable transmission
	Damaged valve
	Damaged ball control

« previos page
Testing of teamwork of an automatic transmission and the engine for the motionless car (F4A42)

next page »
Check the transmission fluid pressure (A4AF3)