REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Jeep Grand Cherokee (from 1993 to 1999, the year of issue)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Jeep
	Grand Cherokee
		Introduction
		Adjustment and routine maintenance
		The straight six-cylinder engine
		The V8 engine
		Procedure of the general and engine major repairs
		Systems of cooling, heating and air conditioning
		The power supply system and exhaust
		The system of electric motor
		Systems of decrease in toxicity of the fulfilled gases and engine management
		Manual box of a gear change
		Automatic Transmission
		Transfer Case
		Clutch and transmission line
		Brakes
		Suspension and steering
			general information
			Removing and installing front stabilizer lateral stability and bushings
			Removal and installation of the front shock absorbers
			Removal and installation of the transverse jet bar front suspension
			Removal and installation of the front suspension arms
			Removing and installing coil spring front suspension
			Removing and installing steering knuckle
			Replacement ball joints
			Removing and installing rear stabilizer rod transverse stability
			Removing and installing the rear shock absorbers
			Removal and installation of the transverse jet bar rear suspension
			Removal and installation of levers of a back suspension
			Removing and installing coil spring rear suspension
			Removing and installing steering wheel
			Condition check, removal and installation of steering gear
			Removal and installation of the steering mechanism
			Removal and installation of the pump system hydrostrengthening steering
			Bleeding the steering system hydrostrengthening
			Wheels and tires - general information
			Corners of installation of forward wheels - the general information
		Body
		The system of on-board electrical equipment
		Controls and operation receptions

printable version

Removing and installing coil spring front suspension

Withdrawal

PERFORMANCE ORDER

Loosen the wheel nuts, Poddomkratte the front of the car and establish it on props. Remove the wheels.
Mark the position and remove the front propeller shaft from the pinion of the differential cross (Chapter Clutch and transmission line), and then tie up the shaft of the piece of wire.
Support the assembly of the bridge jack institutions under the differential or, preferably, two jacks - one on each side of the bridge (the latter is able to provide a better balance). Otboltite the bridge lower suspension arms (Section Removal and installation of the front suspension arms).
Otboltite connecting links (stand) stabilizer and shock absorbers on the front axle suspension (Sections Removal and installation of the forward stabilizer of transverse stability and its sleeves and Removal and installation of the front shock absorbers).
Remove the bracket from the jet bridge post (Section Removal and installation of the transverse jet bar front suspension).
Disconnect the tie rod from the middle of the steering mechanism bipod (Section Checking, removing and installing the steering gear).
Slowly lower the assembly of the bridge so that the spring is fully stretched. If the bridge is backed by only one jack, ask the assistant in the process of lowering the bridge to maintain its right edge. Remove the spring retainer and remove the spring from under the car.

Fasteners coil spring - after the spring is fully stretched Give bolts and remove the holder, then remove the spring through the space between the bridge and the frame.

Check the spring for defects and corrosion that could cause its premature failure.

Setting

PERFORMANCE ORDER

Install the coil spring on the axle, place the holder on the lower coil springs and tighten the bolt holder.
Lift bridge in the loading position and connect it to the crankcase lower suspension arms (Section Removal and installation of the front suspension arms). Tighten fixture with demanded effort.
Connect the tie rod to the middle of the steering mechanism bipod (Section Checking, removing and installing the steering gear).
Fix the jet rod in his arm on the bridge (Section Removal and installation of the transverse jet bar front suspension).
Connect to the front of the axle stabilizer and shock absorbers (Sections Removal and installation of the forward stabilizer of transverse stability and its sleeves and Removal and installation of the front shock absorbers).
Connect the front propeller shaft to the holder crosses pinion differential (Chapter Clutch and transmission line).
Install the wheels and their fastening nut, and then lower the car on the earth. Tighten the wheel nuts to the required torque (see. Specifications to the Head of Adjustment and routine maintenance).

« previos page
Removal and installation of the front suspension arms

next page »
Removing and installing steering knuckle