REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Kia Clarus (1995 issue)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Kia
	Clarus
		Maintenance
		Engines FE DOHC and DOHC T8
		Greasing system
		Cooling
		The power supply system and release
		Fuel system
		Ignition system
		Coupling
		Manual transmission
		ACP G4A-EL
		AKP 50-40 LE
		Axes and power shafts
		Steering
		Wheels and tires
		Suspension
		Body
			Hood
			The trunk lid
			Front bumper
			Rear bumper
			The front door
			Backdoor
			Wipers and windshield washer
			Windscreen
			Windshield
			Rear window
			Dashboard
			The front seats
			Rear seat
			The mechanism of the backrest
			Seat belts
			Door mirror
			Outside rear-view mirror with the electric drive
		The air conditioning system
		Electrical equipment
		Brakes
		Electric schemes

printable version

Backdoor

1 - a cover of the internal handle;
2 - interior doors;
3 - interior doors;
4 - the internal handle assembly;
5 - shield doors;
6 - guiding window "A" / "B";
7 - glass;
8 - windows;
9 - Managing the lock mechanism;

10 - lock the door;
11 - glass guide groove;
12 - edging the door;
13 - door trim and center pad;
14 - the door frame;
15 - seal;
16 - Limiter door opening;
17 - loops.

Withdrawal

PERFORMANCE ORDER

1. Fully lower the glass door.
	2. Remove the internal handle, window handle and the armrest.
3. Remove the door trim and the door lock button.
A warning For vehicles with power windows and locks the door, disconnect the harness connector.
	4. Remove the shield door.
A warning Remove the shield door carefully so that it can be used.
	5. Turn the back of the glass doors down, unscrew the screws and remove the glass door glass door up and out.
	6. Remove the screws and remove window windows working through the hole.
7. Remove the windows, pull and remove the nuts outside handle.
	8. Remove the outside handle.
	9. Remove the holder cylinder door lock and remove the key sub door.
	10. Remove the screws and remove the door lock assembly.
11. Remove the pin stop opening the door.
	12. Remove the hinge bolts the door and remove the door.

Setting

PERFORMANCE ORDER

1. Installation of doors spend to sequences, return to removal, taking into account the following.

2. When installing a triangular vents grease soapy outer perimeter seal.

3. After installing the window, adjust it so that the glass doors easily and smoothly move up and down.

A warning

If necessary, lubricate the door retainer.

Tightening torques, N ??? m
The door lock assembly: 4,2-6,18
Outside handle: 8,8-13
Nut window: 8,8-13
Bolt window: 7,8-11
Doggie door lock: 18-26
Bolt the door hinges: 18-29

Adjustment

PERFORMANCE ORDER

	1. Make sure that the door closes easily, and there was no backlash. If necessary, loosen the screws securing the pawl and adjust the position of the door by moving the dog door lock vertically or horizontally.
2. Check the rear clearance between the door and body. If necessary, adjust the door, door lock pawl moving horizontally. Torque: 18-26 N ??? m

Door hinges

PERFORMANCE ORDER

	1. Open the door, and if the hinges are loose, tighten bolts the door hinges (indicated by arrows).
2. To adjust the gap between the door and body, loosen the door hinge bolts and perform the adjustment. Torque: 17,64-29,4 N ??? m

« previos page
The front door

next page »
Wipers and windshield washer