The car equipment, arrangement of devices and controls

The speedometer indicates the vehicle speed in km / h. below the axis of the indicator arrow is a digital display, the top field is reserved for the odometer (counter full run of the car), the bottom - under the counter current mileage of the trip.

Near the speedometer dial is a pointer to engine speed - the tachometer. Arrow meter shows the driver the speed of the crankshaft in rev / min. Keep the engine speed to be raised so that the arrow pointer sign within the allocated red range of the meter.

Meter detects the temperature of engine coolant. Meter reading may vary depending on the ambient temperature and driving conditions. When you exit the arrow device outside the range of acceptable values of the scale, you should immediately stop movement and allow the engine to cool. Continuous operation overheated engine can cause its failure.

Fuel consumption meter indicates the current fuel level in the tank. When braking, acceleration, maneuvering and driving downhill meter reading may vary slightly. Wiring meter is that it continues to produce business value even when the ignition is switched off. When lowering the fuel level in the tank before the critical works built in in the dial gauge indicator lamp.

AIR BAG

Charge indicator lamp should light up when the ignition is switched on and off immediately after the engine starts. The inclusion of this warning lamp with the engine running warns the driver of infringement of serviceability of functioning of the charge, ie, the battery goes into the discharge. It should be immediately shut down all electricity consumers, on the functioning of which does not depend on traffic safety and to try to avoid stopping the engine, as the attempt to re-start can lead to the final discharge of the battery. The car should be immediately driven away on the nearest car repair shop for fault diagnosis and performance of necessary regenerative repair.

The control lamp of pressure of motor oil should light up when the ignition is switched on and off immediately after the engine starts. Flashing lights when the engine is running indicates the pulsation reducing the working oil pressure in the engine. Move indicator to steady light it indicates that the oil pressure dropped to dangerously low levels, which is fraught with serious internal engine damage, up to the full damage it. In both cases it is necessary to take urgent measures to adjust the oil level to identify and address the causes of the pressure drop.

The indicator lamp lights up briefly when the ignition. Operate it at any other time indicates a possible malfunction of the systems of electric power unit. In the absence of visible signs of failures of functioning of systems of the power unit and reduce the dynamics of the vehicle fixed by the inclusion of a control lamp violation may cause increase in fuel consumption or increase the toxicity of emissions. Ignoring the warning lamp signal lead to serious damage to the engine, until the release of the unit failure. When triggered, the control lamp on the go, stop motion, park in a safe place and stop the engine, and then, after a short time, make a run, while observing the behavior of the warning lamp. If the lamp has not returned to normal operation, and continues to burn, the car should be driven away on the nearest car repair shop for detailed diagnostics and perform necessary regenerative repair. Before troubleshooting engine systems try to drive at a moderate speed, avoiding sharp dispersals with full squeezing the gas pedal.

Even if you restart the engine warning lamp will return to normal mode (ie, off) should be at the first opportunity to consult a workshop, especially if the inclusion of such indicators do not occur for the first time. Continued operation of the vehicle with the included control lamp condition of the engine can lead to premature failure of the catalytic converter. Remember that failures and damage caused by operation of the vehicle with the included control lamp warranty factory n6e apply!

This indicator light comes on at the same time with the inclusion of high beam headlights of the car (see. Below).

This indicator light confirms serviceability of functioning of back foggy lanterns when they are turned on.

Activation of the warning lamp informs the driver of a critical decrease in the level of hydraulic fluid in the brake system.

This warning lamp illuminates at raising the parking brake, reminding the driver to release it before the move. Movement with the cocked lay brake leads to rapid overheating and failure of the brakes on the rear wheels, and premature wear of the tire tread of the rear wheels, and, moreover, may be an infringement of serviceability of functioning of the anti-lock braking (ABS) (See below.). One possible reason for a gradual reduction of the brake fluid level is normal wear and tear of the friction brake linings. At operation of a control lamp the car should be driven away to the nearest service station for evaluation of pads and leak testing of a hydraulic path of brake system.

Short-term operation of a control lamp occurs also when the ignition (even when the parking brake is released).

At a corresponding complete vehicle, this warning lamp lights up when the ignition is switched on and off immediately after the engine is started, thus confirming serviceability of functioning of the circuit anti-lock braking system. Operation of a control lamp in any other situation demonstrates the identification self-diagnosis system disorders circuit ABS. The car should drive off without delay to the nearest service station for detailed diagnostics of the system and the implementation of necessary regenerative repair.

When the alarm control lamp turns off anti-lock brakes, but the car brakes continue to function as usual, providing adequate braking of the vehicle.

At a corresponding complete vehicle, this warning lamp lights up when the automatic control system of the vehicle speed (Tempostat) (See below.).

The glow of the warning lamp warns the driver that not all car doors slammed tight.

Indicator confirms and serviceability of functioning of the direction indicators of the vehicle and operates in flashing mode with a frequency corresponding to the flashing indicator. Rapid flashing light usually indicates a blown bulb of one of the direction indicators. It should be as soon as possible to replace the burnt-out bulb, so as not to accidents on the roads.

Blinking of this indicator is usually accompanied by the inclusion of an alarm.

This indicator light comes on when the fuel tank is less than 9.0 liters of fuel and warns the driver of the urgency to produce refueling the car.

This indicator light comes on when the transfer key overdrive switch to OFF.

.

1. Main switch lighting control is designed as a lever mounted in the left side of the steering column directly under the steering wheel.

Flash of beam shall no matter what position is turning the handle end of the main switch.

Fog lights should only be used when visibility is poor!

1. Turn on / off the fog lamp is made by turning the appropriate position ring switch on the handle of the lever assembly of the left combined switch.

Navigation lights should be included.

2. Turning back foggy lanterns are also made by means of a ring switch. Navigation lights should also be included.

Turning cleaners / washers of a windscreen can be made only when the ignition (ON and ACC). Selection of operating modes is made by moving the wiper lever switch up / down. Options Intermittent wiper operation (range 2-20) can be selected using the handle on the front end of the lever.

Do not include washers longer than 30 seconds. Do not make attempts to include washer when emptying the tank system. In frosty weather, wipers should be included only after the windshield is warmed.

Misuse Tempostat may cause a traffic accident. Operate the speed control only when driving on motorways and free under favorable weather conditions. During operation of the system can occur automatically move the gas pedal, which in this case should not hold the foot in order to avoid damage to the reference axis and mechanisms.

The lever switch of management of functioning Tempostat located to the right above the steering column, the assembly below the right combination stalk. Enable / disable the system is made by means mounted in the handle end of the stalk and is accompanied by a button triggering the appropriate warning lamp on the dashboard of the car.

The controller starts to operate only when the navigation lights (see. Above).

The controller is located in the center console between the keys of the car seat heating switches and provides the possibility of adjusting the direction of the optical axes of the headlights radiation mode beam and achieve the best lighting conditions for different road vehicle loading.

1. The front seat of a vehicle equipped with built-in heaters. Seat heating control switches are located on the center console of the car.

1. Turn on the alarm is made by push-button switch mounted in the central part of the dashboard of the car (under the deflectors central duct ventilation / heating the interior) and is generally equipped with a control lamp icon depicting two inscribed into one another triangle.

When the alarm direction indicators will not function!

2. The control panel functioning of the electric drive of the top hatch is located on the roof console of the car.

7. In case of refusal drive hatch cover can be brought into the closed position manually. Remove the trim panel motor control, - is due to open access to the end of the drive shaft of the electric motor. Using a suitable size wrench rod, crank shaft clockwise until the hatch is not fully closed. To lower the cover of the angular position of crank shaft counterclockwise. In order to eliminate the causes of failure of the actuator, contact a workshop.

1. Assembling the functioning of the electric control outside rearview mirror mounted in the dashboard of the car to the left of the steering column. Mirrors made by means of a slide, and the key switch panel as follows:

a) Turn the ignition switch (ACC ON and key);
b) Move the lever to slide switch to the left (L) or right (R) make a choice to be mirrors;
c) Click on the top, bottom, left or right sectors key switch, make adjustments to the position of the selected mirror;
d) Once the adjustment of both mirrors move the lever to slide the switch to the middle position, in which the adjustment button does not operate. This is to ensure that when a button is accidentally pressed not to disturb the adjustment of the exterior mirrors.

2. provided as folding mirrors in the parking position. To do this, press down on the mirror in the direction of the "back".

1. Turn on the electric-allows you to remove from the surfaces of the rear window / door mirrors condensation, frost or even a thin ice. When the electric heater lights built into the switch button indicator light. Turn off the heating is carried out by pressing the button.

Assembling the control operation of the electric exterior mirrors mounted in the dashboard of the car to the left of the steering column. Mirrors made by means of a slide, and a joystick switch panel as follows:

a) Turn the ignition switch (ACC ON and key);
b) Move the lever to slide switch to the left (L) or right (R) make a choice to be mirrors;
c) Using a joystick switch make adjustments to the position of the selected mirror;
d) Once the adjustment of both mirrors move the lever to slide the switch to the middle position, in which the adjustment button does not operate. This is necessary to ensure that an accidental push of a button does not disrupt the adjustment.

You can automatically translate the driver's door window in one of the end positions (fully open or fully closed), it is sufficient briefly press the AUTO button control panel driver's door. In order to stop the process of opening / closing the window, click on the button again.

Push-button mounted in the center section of the instrument panel trim vehicle between the switch and control lamp Tempostat anti-theft alarm. Operation of the system takes place only when the ignition is switched on. The liquid is supplied to the lens range from the same reservoir as the windshield - periodically check the level.

Inclusion of washers with an empty tank is fraught with failure due to overheating of the electric motor of a submersible pump!

Do not use Tempostat when driving on busy roads, on the streamer in the hilly and mountainous areas, with slippery road surfaces and strong winds.

3. Accelerate the vehicle to the desired speed and press the SET / COAST on the control panel functioning Tempostat - the display should come on board processor inscription CRUISE.

See. Information concerning the proper and safe steering column.

Implementation of adjustment of the steering column while driving can lead to loss of control of the vehicle and can lead to serious traffic accidents!

2. In order to adjust the steering column adjustment is necessary:

a) Lower the left under the steering wheel lock lever to lock the steering column;
b) Adjusting the steering wheel position adjustment is performed by moving it in the desired position in the vertical plane. Properly adjust the steering wheel should not obstruct the review of the instrument panel;
c) After the adjustment, lock the steering column lock lever fully returned to its original position;
d) Check reliability of fixing column, trying to move it up and down.

For charging the parking brake fully lift up the lever located between the front seats. Releasing the parking brake as follows: pull the lever up slightly, press the release button on the end of the handle, and then lower the lever down. When you release the parking brake corresponding indicator lamp mounted in the dashboard of the car, should go out (see. Above in this section).

Stir with a cocked parking brake can lead to failure of the brake hubs and bearings of the rear wheels!

Manual transmission shift lever is located on the center console of the car. On top of his arm affixed shift patterns.

AT gear selector lever is also located on the center console of the car. On the side of the lever on the handle is a button unlock, which should squeeze switching transmission in position "P", "R", "2" and "1".

Below the unlock switch located overdrive (O / D). When pressing the button "O / D" is switched off raising transfer (while warning lamp "O / D OFF"). To turn On / D press again.

Overdrive functions only when warmed to normal operating temperature of the engine. When the mute button Tempostat overdrive ceases to operate.

On models with AT provides for a choice of operating modes of transmission. Mode switch located on the center console of the car to the left of the AT selector lever and allows you to select one of three modes: AUTO, SNOW AND SPORTS (see. Section Methods of operation).

3. To adjust the seat position in longitudinal direction of the bracket, pull up on the front of a seat cushion and hold it in a raised position, slide the seat assembly forward or backward at any convenient position. Release the clip to test the reliability of locking seat, try to move it back and forth.
4. To change the angle of the seat back, pull it forward, lift the lever on the side under the seat cushion by the door, then hold the lever in the raised position, adjust the backrest. Back fixing in the new position takes place automatically when you release the lever.

5. Some embodiments provide the ability to adjust the vehicle height of the seat cushion. Adjustment is made by means of two handles disposed on the outer side of the pillow.

1. In some models include electric adjustment of the driver's seat. Functioning of the electric control panel with two switches located on the left side of the seat cushion. Combined elongated slide switch is used to adjust the seat position in longitudinal and vertical directions. When the switch is carried out smaller tilt back.

4. Adjustment of the height position of the front and rear edges of the seat cushion is performed by squeezing the corresponding side of the front or rear ends of the slide switch (1). Adjusting height of the cushion assembly is performed by moving up or down the entire switch.

6. Adjust the amount of bending of the lumbar back (with appropriate equipment) made by means of a lever located on the back of the seat assembly.

On some models, a possibility of heating the front seats (see. Above).

Do not turn the heated seats with the engine off, and try not to use it for a long time with the engine running at idle speed to prevent battery discharge.

On some models, the rear seat is equipped with a center armrest. The armrest is located in the central part of the seat and expanded by pulling out a niche in the back and lower to a horizontal position. After lowering the armrest offers access to the luggage compartment of the vehicle.

Some embodiments provide for a vehicle lock button headrest. With this structure in order to raise the head restraint, just pull it up, lowering the same can be made only after a push-button lock.

Adjusting the angle of the head rest is done manually.

There are two full-time position of the rearview mirror, one designed to run in the daytime, and another - in the dark. In the second position, the reflectivity of the mirror is reduced, which helps to reduce glare of headlights moving behind vehicles. Translation mirror daily position at night and back made using a special, built in the bottom of the lever assembly. By pressing the lever forward or backward to select the desired position of the mirror.

Also provides for the possibility of folding mirrors in the parking position. To remove the rear-view mirror in the parking position just push it to the glass door of the car.

Setting the clock indication is made by pressing the "H" minute - by pressing the "M".

If you turn off the instrument panel lighting brightness indicator hours reduced.

At a corresponding complete vehicle display board processor is built into the tachometer dial. With the ignition on, you can select one of the possible modes of operation of the display. The selected mode is indicated by a special cursor in the shape of a triangle. The display can be used to highlight the time, outdoor temperature, the distance that can be covered without refueling, the length of the distance traveled, journey time, average speed and average fuel consumption.

Switching the display is a special button.

Business card holder and cup holder mounted in the assembly of the center console behind the handbrake lever.

In front of the center console, under the assembly mounted audio small storage compartment for storing small items. There are two designs of small glove box - sliding and swing.

The cigarette lighter operates only at two positions of the ignition key: "ACC" or "ON", when the ignition is on or the power auxiliary consumers. To activate the cigarette lighter to drown his button click. After the heating coil button automatically snaps back to its original position.

To avoid the cigarette lighter of the system, it does not hold the button during the heating coil!

Pulling an additional panel in the first position, the visor can lead to the closing of mirrors!

1. Switch the front (main) interior lamp has three fixed positions. In position "0" the interior light turns on when you open any of the doors of the passenger compartment.

The roof console of the car encased also directed two individual lamp. Switches individual lamps are located near the respective lamp shades (left and right). To activate the lamp, press the corresponding switch. To turn off the illumination, press the same button again. Individual lamps operate at any position of the ignition key.

Voltage onboard power supply of 12 volts, do not connect to the socket PTO consumers with the parameters of more than 12 V / 120 Watt. Not used outlet should be closed by a special cover.