| Type of system | E 4-channel / 4-sensor ABS with electronic brake force distribution and Brake Assist (possible on request). Ventilated disc front, drum or drum rear, diagonal circuit, amplifier gidrovakuumny |
| The type of fluid | See. Chapter Settings and maintenance |
| Disc brakes |
| Front brake |
| Type |
| Models 1993 and 1994 MY | CL25VB |
| Models from 1995 MY. | CL25VB or CL25VE |
| The diameter of the cylinder bore, mm |
| CL25VB | 57.2 |
| CL25VE | 40.2 |
| The geometrical parameters of pads (length x width x thickness) mm |
| CL25VB | 125.6 x 45.3 x 11 |
| CL25VE | 140.0 x 45.3 x 11 |
| The geometrical parameters of the brake disc (diameter x thickness) mm |
| CL25VB | 280 x 22 |
| CL25VE | 280 x 26 |
| Rear brake |
| Type |
| Models 1993 and 1994 Vol. | CL9H |
| Models from 1995 MY. | CL9HB |
| The diameter of the cylinder bore, mm |
| CL9H | 33.96 |
| CL9HB | 33.96 |
| The geometrical parameters of pads (length x width x thickness) mm |
| CL9H | 75.0 x 40.0 x 9 |
| CL9HB | 89.1h 39.5 x 10 |
| The geometrical parameters of the brake disc (diameter x thickness) mm |
| CL9H | 258 x 10 |
| CL9HB | 9 x 278 |
| Minimum permissible thickness of the brake pads | See. Chapter Settings and maintenance |
| Minimum permissible thickness of the brake disk, mm | See. Cast on the disc labeling |
| The maximum permissible value of the brake disc runout mm |
| The front brakes | 0.07 |
| The rear brakes | 0.15 |
| The maximum allowable amount of thickness variation of a brake disk, mm |
| The front brakes | 0.01 |
| The rear brakes | 0.02 |
|
Drum brakes of the rear wheels |
| The minimum admissible thickness of frictional overlays of brake boots, mm | See. Chapter Settings and maintenance |
| The maximum allowable inner diameter of the drum, mm | See. Cast on the disc labeling |
| The maximum permissible value of roundness of the drum, mm | 0.03 |
| The main brake cylinder
|
| The diameter of the cylinder bore, mm | 23.81 |
| Vacuum brake booster |
| Type |
| Models 1993 and 1994 Vol. | M195-V1125T |
| Models from 1995 MY. | M215T |
| The diameter of the aperture, mm |
| M195-V1125T |
| Primary iris | 205 - 230 |
| The secondary aperture | 180 - 205 |
| M215T |
| Primary iris | 230 |
| The secondary aperture | 205 |
| The length of the output push rod, mm | 10.275 ÷ 10.525 |
| The distance from the amplifier assembly to split pin rod, mm | 125 |
| Adjust the brake pedal |
| The height of the Up state, mm |
| Models with Manual transmission | 159 ÷ 165 |
| Models AT | 169 ÷ 174 |
| Free lift, mm | 0.04 ÷ 0.12 |
| The height of the pedal is depressed, mm |
| Models 1993 and 1994 Vol. | 90 |
| Models from 1995 MY. |
| Models with Manual transmission | 70 |
| Models AT | 75 |
| Parking brake |
| Drive | Lever |
| The number of clicks of a ratchet at applying force of 20 kgf |
| Models 1993 and 1994 Vol. | 8 ÷ 10 |
| Models from 1995 MY. | 10 ÷ 11 |
| The number of clicks of a ratchet to trigger the gauge-switch of a control lamp |
| Models 1993 and 1994 Vol. | 1 ÷ 2 |
| Models from 1995 MY. | 1 |
| The gauge-switch of stoplights
|
| The gap between the plug gauge-switch and stop the pedal, mm | 0.3 ÷ 1.0 |
| Efforts of a tightening of carving connections | Nm |
| Nuts of fastening of the servo brake servo |
| Models 1993 and 1994 Vol. | 8 ÷ 11 |
| Models from 1995 MY. | 13 ÷ 16 |
| Caliper mounting bolts (front and rear disc brakes) | 22 ÷ 31 |
| Bolts anchor bracket |
| The front brakes | 72 ÷ 97 |
| The rear brakes | 38 ÷ 52 |
| Hollow bolt choke assembly brake hose connected to the caliper brake (front or rear) | 17 ÷ 20 |
| Bolts wheel cylinders | 6 ÷ 11 |
| Gates pumping calipers and wheel cylinders | 7 ÷ 9 |
| Nuts of fastening of the GTZ |
| Models 1993 Vol. | 8 ÷ 11 |
| Models 1994 Vol. | 12 ÷ 15 |
| Wheel bolts | See. Chapter Settings and maintenance |
