 printable version
Removing and installing the generator
The car has a three-phase AC generator. Depending on the model and equipment can be installed generators of various capacities.
 | If subsequently installed on the vehicle electrical appliances with high power consumption, it is necessary to check whether there is enough available capacity of the generator. If necessary, install a new generator of a higher power. |
AC voltage generated by the generator, the rectifier diode is converted into a DC voltage that produces the battery charge. The controller changes the charging current so that the operating voltage regardless of the number of revolutions was kept constant.
| The generator can be replaced. A damaged alternator repaired or when buying a new generator is taken Ladder. So take away the failed generator itself. |
Gasoline engines 111, 112
Withdrawal
| 1. Disconnect the negative (-) cable of the battery when the ignition is off. You must first remove the air filter box of the passenger compartment. | Before disconnecting the cable, find out the radio security code, if any, address to Section Replacement of the battery.
Do not connect an auxiliary power supply. |
2. Engine 111: Remove the air filter, refer to Section Removal and installation of the air filter.
3. Engine 112: Remove the air intake duct on the front passenger side.
4. Remove the V-belt, address to Section Removal and installation of the V-belt.
5. Remove the protective cover (4) and remove the fat (B +) wire (1) from the terminal 30.  | 6. Disconnect (D +) wire (2) from the terminal 61. |
7. Remove the bolts (3). Remove the spacer sleeve top bolt and remove the generator from the engine compartment upward. |
|
Setting
| 1. Place the generator in place and secure it with torque 42Nm.  | Note spacer sleeve top bolts. |
2. Attach the wire to the terminal (B +) of the generator indicated in the Specifications effort.
3. Put on the terminal 30 protective cap.
4. Secure the generator (D +) wire 5Nm moment.
5. Put the V-belt, address to Section Removal and installation of the V-belt.
6. Engine 111: Install the air filter housing, refer to Section Removal and installation of the air filter.
7. Engine 112: Install the air intake duct.
8. Connect the earth cable (-) battery when the ignition is switched off. Replace the cabin air filter box. If necessary, enter the code for the radio and set the time on the clock. |
|
Diesel engines
Withdrawal
| 1. Disconnect the negative (-) cable of the battery when the ignition is off. You must first remove the air filter box of the passenger compartment. | Before disconnecting the cable, find out the radio security code, if any, address to Section Replacement of the battery.
Do not connect an auxiliary power supply. |
2. Remove the cover of the engine, address to Section Removal and installation of the engine cover.
3. Remove the V-belt, address to Section Removal and installation of the V-belt.
4. Remove the hose duct and the air intake on the passenger side.
5. Remove the hose clamp and charge air pipe from the turbocharger.
6. Remove 3 bolts and remove the pipe.
7. Lift and establish on supports a forward part of the vehicle.
8. Remove the bottom, refer to Section Checking the engine by means of the vacuum gauge.
9. Drain the radiator, refer to Section Replacement of a cooling liquid - general comments.
10. Disconnect from the generator coolant feed line.
11. Remove the stabilizer bar front suspension, also refer to Chapter Suspension and steering.
12. Remove the protective cover and remove the thick wire (B +) of the terminal 30 (1).
 | 13. Disconnect (D +) of the terminal 61 (2). |
14. Remove 2 bolts and take aside the high pressure pipe steering.
15. Remove 3 bolts and remove the holder.
16. Remove the bolts (3) and remove the generator down from the engine compartment. |
|
Setting
| 1. Place the generator in place and secure it with bolts to 20Nm. Thus replace the gasket between the flange of the housing of the radiator and the crankcase.
2. Secure the conduit for supplying coolant to the generator, replace the O-ring at the same time.
3. Fix the holder.
4. Attach the high pressure pipe steering.
5. Attach the wire (B +) 14Nm torque on the generator and put the cap on the terminal 30.
6. Secure the wire on the alternator (D +).
7. Replace the stabilizer.
8. Fill the system with coolant, refer to Section Replacement of a cooling liquid - general comments.
9. Install the bottom cover, refer to Section Checking the engine by means of the vacuum gauge.
10. Lower the car on wheels.
11. Secure the pipe combustion air to the turbocharger and attach a hose.
12. Replace the channel and the air intake hose.
13. Put the V-belt, address to Section Removal and installation of the V-belt.
14. Install the engine cover, refer to Section Removal and installation of the engine cover.
15. Connect the earth cable (-) battery when the ignition is switched off. Replace the cabin air filter box. If necessary, enter the code for the radio and set the time on the clock. |
|
|
