add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Passat B6 (from the year 2004)

general info. full specifications. diagnostics. hints. tips. tricks
Volkswagen Passat B6
Home
 
Volkswagen
Passat B6
Operation and maintenance of car
Engine
Overview
Mechanical (engine capacity of 1.6 liters)
Removal and installation of the top casing of the engine
Check the timing belt (4-cyl. Petrol engines of 1.6 liters)
Removing Engine
Engine installation
Disassembly and assembly of the engine
Removing and installing V-ribbed belt
Removing and installing timing cover
Replacing crankshaft oil seal on the side of the pulley
A method of tightening the mounting bolt sprocket belt drive
Dismantling and assemblage of pistons and rods
Cylinder Head
Checking the valve timing
The timing
Removing and installing the camshaft housing
Removal and installation of the cylinder head
Compression Test
Repair the valve mechanism
Checking the valve guides
Replacing valve stem seals
Lubrication system
Cooling system
Fuel Injection System
The mechanical part (petrol engines of 2.0 liters)
Lubrication system
System ohlazhdeiya
Fuel system
Injection system
System of release of gases otrabotavschih
Ignition system
The mechanical part (diesel engines of 2.0 liters)
Lubrication system
Cooling system
Fuel system
Turbocharging turbo running on exhaust
The direct injection diesel
Exhaust
Tables
Transmission
Chassis
Steering Gear
Brakes
Onboard electric
Body
diagrams
 


Hit Counter by Digits


print page printable version

Removing and installing the camshaft housing



NOTE
In this engine camshafts arranged in the camshaft housing. Before removing the casing must be removed camshaft timing cover.
Seating surfaces crankcase the camshaft can not be processed.

Withdrawal
First, you must check whether the car radio with coding. If so, you should know the security code.
Disconnect the ground cable from the battery when the ignition is switched off.
Remove the timing cover.
Rotate the crankshaft to TDC of the first cylinder, then turn the crankshaft back against the direction of rotation of the motor by about 45 ?� and remove the camshaft sprocket with timing chain.
Remove the EGR valve and remove the camshaft cover.
Disconnect plug the fuel pressure sensor for low pressure.
Remove the earth cable from the crankcase the camshaft.
Remove the ignition coil. To do this, use a wheel puller.
Remove the box with wiring harness to the crankcase the camshaft.

The plug and fuel supply
Fig. 2.39. The plug and fuel supply


Disconnect and plug the fuel supply line from the high-pressure pump (Fig. 2.39).
Remove the guide and remove the clip from the high-pressure line.

NOTE
When loosening the union nut hold the threads on the high pressure pump and the bottom of the intake manifold with a wrench.

Unscrew the union nuts 3 and 1 line of high pressure.
Disconnect the plug from the Hall sensor.
Remove the dipstick.
Remove the lower part of the intake manifold.
Remove the left eye for hanging.
Loosen and remove the fixing bolts from the camshaft housing edges to the center, alternating crosswise.
Carefully lift camshaft housing.

Setting
Remove any residual sealant from the cylinder head and camshaft housing standard sealant remover.

NOTE
Pistons not be located at TDC.

Do not allow dirt and sealant residue in the cylinder head.
Thoroughly clean seating surfaces. They must be free of oil and grease.
Turn the inlet and exhaust camshafts until camshaft holder will not enter the holes in the camshafts to the stop.
For fastening clamp screw M6 bolt by hand; without tightening.

Applying sealant
Fig. 2.40. Applying sealant


Apply sealant to clean the seating surface of cam housing a thin uniform wiring. See the shaded area in the figure 2.40.

NOTE
Harness sealant should not be too thick, otherwise the excess sealant may get into the oil passages, leading to engine damage.


Installation of the valve stem in the corresponding support elements
Fig. 2.41. Installation of the valve stem in the corresponding support elements


Make sure all the right levers roller attached to the ends of the valve stems zaklipsovany 1 and the corresponding support element 2 (Fig. 2.41).
Before installing the camshaft housing, screw the two spacers (M6x80) in the cylinder head.
Gently replace the camshaft housing vertically on top of the spacer bolts and the cylinder head dowel pins.

NOTE
Do not spill oil on the adjacent surface.

Tighten new fixing bolts of the camshaft housing crosswise, alternately from the center outwards.
Make sure that the camshaft housing is not warped. Tightening torque 10 Nm + to tighten 1/4 turn (90 ?�)

NOTE
After installation of the camshaft housing sealant must be dry in about 30 minutes.

Adjust the timing.
Further installation is performed in reverse order.
Install the timing cover.
Connect the fuel lines.
Install the EGR valve




« previos page
The timing
next page »
Removal and installation of the cylinder head

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.