 printable version
Demolition, removal, installation and adjustment of doors
The front doors The design of the front door assembly Disassembly, removal and installation | - Disconnect the negative wire from the battery.
- Remove the interior door trim.
 | - Remove the two screws and remove the bracket poruchnevoy handle.
|
 | - Remove the four mounting bolts, liberate from clamps on the door frame wiring harness and speaker speaker. Disconnect the connector and remove the speaker.
|
- Separate door insulation film screen.
- Connect the battery and - if disconnected, - the wiring gear selector window. Turn on the ignition and the lower half of the door glass. Switch off the ignition and disconnect the wire from the battery.
- Through the opening in the door frame to remove the two screws on the glass to the window regulator.
 | - Leaning forward, carefully remove the glass from the window opening of the door.
|
 | - Disconnect the electrical wiring from the motor drive control window, give six nuts and through the service port, remove the regulator assembly from the door frame.
|
 | - Remove the guide groove (1) of the window opening.
|
 | - Remove one mounting bolt and through the service port, remove the glass run from the door frame.
|
 | - Rotate counter-clockwise and remove the door lock release button.
|
- Disconnect the two drive shaft from the outside door handle.
 | - Remove the three mounting bolts through the service port and remove the door frame a locking assembly.
|
- On the right door gave two fastening nuts and remove the actuator lock.
- Give two fixing nuts and remove the outside door handle.
- Remove the door mirror (see. Section Removal and installation of door mirrors).
- Disconnect the five-pin connectors laid wiring inside the door frame.
- Through the service port, remove the wiring from the frame.
 | - Gently shake a finger with a hammer stroke limiter doors - try not to damage the paintwork.
|
- Give two fixing screws and remove the stopper.
- Remove the boot door threshold.
 | - Remove the four hinge screws and remove the door from the car - use the help of an assistant.
|
 | - If necessary, remove the trim panel of the door threshold and the lower section of B-pillar and remove the mounting flange sealing strip doorway.
|
- Installation is the reverse order of the dismantling of the components - track compliance Specifications Chapter Body to the efforts of a tightening of threaded fasteners.
- Check the landing doors in the Touring Car opening, if necessary, make appropriate adjustment.
|
|
Adjustment | - Release hinge screws and align the door in the opening relative to the surrounding body panels. After finishing the adjustment, be sure to tighten the bolts with demanded effort.
- Check the door lock clicks into place. If necessary, release the fixing bolts and tweak the position of drummer.
 | By displacement of the striker in the horizontal direction can be aligned with the position of the rear edge of the door is closed to the surface of the rack. |
|
|
Rear doors The procedure is similar to the procedures described above for the front door, adjusted for differences in the design of assemblies. The design of the tailgate assembly Tailgate The design of the tailgate assembly Disassembly, removal and installation | - Disconnect the negative wire from the battery.
- Open the tailgate.
- Remove the two screws and remove the door stoplight top level.
- Disconnect the wiring, remove the two screws and remove the stop light.
- Disconnect the two pin connectors (one on each side of the door assembly), disconnect the wiring of the rear screen.
- Remove the grounding lug right heater wiring connector.
- Release the latches 12 and remove the bottom panel of an internal upholstery of a door.
- Remove the plastic cover on the left of the central opening in the door frame, and through the service port disunite three pin internal wiring of the door.
- Disconnect the three one-pin connector located in the upper left corner of the door assembly.
- Remove the planting hole in the upper left corner of the door rubber grommet and release from the door frame wiring harness.
- Remove the pins from the socket stoplight and one pin from the left window heater connector.
- Carefully release the cable harnesses of the cable channel in the door frame, as well as the guard and the rubber grommet.
- Secure shell connectors with their pins.
- Release of the door frame right grommet, thus providing access to the liquid feed tube to the nozzle washing the rear window.
- Remove the nozzle and disconnect the feed tube.
 | - Enlisting the support of an assistant, securely lock the tailgate in the open position and disconnect the door from the spherical bearing telescopic stops.
|
- To facilitate the installation procedure squeeze a protective cover and secure it with the outside of the supply hose connector.
- Disconnect the supply hose from the connector ?�
and remove it from the vehicle.
 | - Remove one looped bolt.
|
- After ascertaining the reliability of locking the doors, turn out the remaining two bolts and remove the door assembly from the vehicle.
- Installation is the reverse order of the dismantling of the components - track compliance Specifications Chapter Body to the efforts of a tightening of threaded fasteners.
- Check the landing doors in the Touring Car opening, if necessary, make appropriate adjustment.
|
|
Adjustment |  | - Perform control measurements A, B and D, and make sure that the measurement results are within the allowable range, if necessary, release the hinge screws and spherical bearings telescopic stops and tweak the position of the door opening in Touring Car. Having finished adjustment, tighten the bolts and support with demanded effort.
|
 | - Perform control measurement C - established position on the side stacks of body opening wedge angle determines the closing of the door to a C. If the measured value exceeds the limit, push the wedges out - to increase the size should be, on the contrary, to move the wedges to the side of the opening.
|
|
|
|
