CAUSE | REMEDY |
Too much idle path of the brake pedal |
Fully or partially worn friction linings
| Replace the brake friction linings. |
The failure of one of the brake circuits | Check the brake circuits for leakage of brake fluid. |
Brake pedal goes away when you press and springs |
The air in the brake system | Bleed the brakes. |
Too little brake fluid in the equalizing tank | Top up with new brake fluid. |
Friktsionnnye rear brake pads are worn out, the fee covers the base adjacent to the spring | Replace the friction linings. Use branded friction linings. |
The formation of steam. Occurs when a heavy load, for example, when driving on the pass | Replace brake fluid. Bleed the brakes. |
Sly the brakes, the brake pedal should be pressed to failure |
Leaky pipeline | Tighten the connection of the pipeline elements, or replace it. |
Damage to the cuff or in the main wheel brake cylinder | Replace cuff. If the damage of the cuff in the master cylinder, replace internal details or the cylinder itself. |
Damage to the stationary rubber gaskets | Repair support. |
Poor inhibitory effect despite the strong depression of the brake pedal |
Greasy friction linings | Replace the friction linings. |
Unsuitable or cured friction lining | Replace the friction linings. Use only genuine friction linings. |
Faulty Brake Assist | Check usiliteltormozheniya. |
Seized piston | Provide free stroke support. |
Contamination of the hydraulic system | Clean, replace the brake fluid. |
Worn friction linings | Replace the friction linings. |
The brakes squeak |
Worn friction linings | Replace the friction linings. |
Often the result of atmospheric influences (humidity) | No events if there is creaking after a long parking lot at high humidity and after the first braking is not repeated. |
Unsuitable friction lining | Replace the friction linings. Use branded friction linings. Cover the bottom lining paste anti-creak. |
Brake caliper disc rotates nonparallel | Check the contact surface of a support. |
Contaminated wells in the caliper | Clean caliper wells. |
Improper installation of the pistons in the calipers of the rear wheels | Check out the 20-degree setting pistons. |
The brakes are blocked with gentle braking |
Not oiled friction linings | Replace the friction linings. |
Brake delayed spontaneously |
Clogged compensation hole in the brake master cylinder | Clean the brake master cylinder and replace internal components. |
Too small a gap between the control rod and the master cylinder piston | Check the clearance (working in a repair shop). |
The friction linings are not separated from the brake disc, wheel hard to turn by hand |
Corrosion in the support cylinder | Caliper Repair if necessary - replace. |
Uneven wear pads |
Unsuitable friction lining | Replace the brake pads. Use branded friction linings. |
Contaminated caliper | Clean caliper wells. |
Tight Stroke | Check the piston. |
Leaking brake system | Check the tightness of the brake system. |
Pulsating brake pedal |
Too much tolerance for lateral runout or thickness of the brake disc | Check the runout and clearance. Modify or replace the brake disc. |
The brake disk rotates not in parallel a support | Check the contact surface of a support. |
The functioning of the ABS anti-lock | It does not require any activities normal |
Vibration brakes |
Unsuitable friction lining | Replace the friction linings. Use only genuine friction linings. |
Partial corrosion of the brake disc | Gently smooth out the grinding disc pad. |
Lateral runout of the brake disc | Modify or replace the brake disc. |
Brake pedal is lowered slowly when lightly pressed |
Faulty brake master cylinder | Replace the brake master cylinder. |
The unilateral action of the brake |
The air pressure in the tires is not within the specified | Check tire pressure and adjust. |
Uneven tire wear | Replace worn tires. |
Greasy friction linings | Replace the friction linings. |
Faulty wheel suspension or steering | Check |
And diversified types of pads on the same axle | Replace the friction linings. Use branded lining. |
Poor contact friction linings | Replace the friction linings. |
Clogged pipe | Check the brake pressure of all four brakes. |
Contaminated wells caliper | Clean the surface of the landing and guide surface friction pads in the caliper. |
Corrosion in the support cylinder | Replace the caliper. |
Uneven wear of the friction linings | Replace the friction linings (both wheels). |
Brakes heat up during movement |
Clogged compensation hole in the brake master cylinder | Clean the brake master cylinder and replace internal components. |
Unsatisfactory idling brake master cylinder pushrod | Check for sufficient clearance between the pedal and the push rod and, if necessary, adjust. |
Jamming of the brake piston or stiffness | Restore patency. |
Clogged brake line | Clean truboporovody, replace the brake fluid. |
Improper adjustment of the parking brake | Properly adjust. |