add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Mercedes-Benz C-Class (W203, 2000 issue)

general info. full specifications. diagnostics. hints. tips. tricks
Mercedes-Benz W203
Home
 
Mercedes-Benz
W203
Introduction
Instruction Manual
Routine maintenance
Engine
Cooling and heating
The power supply system and release
Electric motor
Manual gearbox
Automatic Transmission
Coupling and power shafts
Brakes
Suspension and steering
Body
Onboard electric
Specifications
Fault diagnosis onboard electric equipment - the general information
Check the wiper motor
Check heated rear window
Relays and fuses
Replacing incandescent exterior lights
Replacing bulbs Interior lighting
Removing and installing daylight sensor
Removing and installing lights
Removing and installing fog
Removing and installing the lens fog
Removing and installing the rear light
Replacing the battery ignition key / remote control
Removing and installing windscreen wiper motor
Removing and installing rear window wiper motor
Removal and installation of the water tank and pump motor
Removal and installation of a rain sensor
Removal and installation of the audio signal
Removing and installing parking sensors
Removing and installing ambient temperature sensor
Removing and installing dashboard
Removal and installation of stalk
Removal and installation of the switch of the front canopy on the ceiling
Removal and installation of the group switches to the left of the control panel
Removing and installing center console switch
Removal and installation of switches in the door
Removal and installation of door switches the interior lighting
Removal and installation of warning signs parking assistant
Removing and installing cigarette lighter
Removal and installation of the radio
Removal and installation of loudspeakers
The digital CAN data bus
The uniform lock - general information
Installation of additional electric and electronic devices
Function and location of electrical connectors
Diagrams
 


Hit Counter by Digits


print page printable version

Removal and installation of loudspeakers



Speaker at the door

PERFORMANCE ORDER

1. Disconnect the negative (-) cable of the battery when the ignition is off. You must first remove the air filter box of the passenger compartment.

Before disconnecting the cable, find out the radio security code, if any, address to Section Replacement of the battery.

2. Remove the door trim, refer to Section Removal and installation of front doors facing.

3. Disconnect the connector (1) of the speaker.

4. Remove the 3 screws (arrows in the illustration) and remove the speaker from the body of the door.


Setting

PERFORMANCE ORDER

1. Installation is performed in reverse order of removal.
2. Attach a weight cable (-) battery when the ignition is switched off. Replace the cabin air filter box. If necessary, enter the code for the radio and set the time on the clock.


Tweeter in the front doors

Withdrawal

PERFORMANCE ORDER

1. Disconnect the negative (-) cable of the battery when the ignition is off. You must first remove the air filter box of the passenger compartment.

Before disconnecting the cable, find out the radio security code, if any, address to Section Replacement of the battery.

2. Remove the triangular patch, refer to Section Removal and installation of the triangular plates.

3. Disconnect the connector (1) high-frequency loudspeaker.

4. Carefully release the locking tabs with a screwdriver (arrow in the illustration) and remove tweeter of the triangular plates.


Setting

PERFORMANCE ORDER

1. Installation is performed in reverse order of removal.
2. Attach a weight cable (-) battery when the ignition is switched off. Replace the cabin air filter box. If necessary, enter the code for the radio and set the time on the clock.


The speaker in the instrument panel

Withdrawal

PERFORMANCE ORDER

1. Disconnect the negative (-) cable of the battery when the ignition is off. You must first remove the air filter box of the passenger compartment.

Before disconnecting the cable, find out the radio security code, if any, address to Section Replacement of the battery.

2. Remove the vents of the instrument panel, refer to Section Removal and installation of vents.
3. Disconnect the speaker connector.
4. Use a screwdriver to remove the speaker from the back side vents of the holder, and then from the dashboard.


Setting

PERFORMANCE ORDER

1. Insert the speaker in the holder and secure.
2. Dock connector.
3. Insert the upper vents and fasten with four screws.
4. Insert the cover in the dashboard and fix.
5. Connect the earth cable (-) battery when the ignition is switched off. Replace the cabin air filter box. If necessary, enter the code for the radio and set the time on the clock.


The speaker in the shelf

Sedan

Withdrawal

PERFORMANCE ORDER

1. Disconnect the negative (-) cable of the battery when the ignition is off. You must first remove the air filter box of the passenger compartment.

Before disconnecting the cable, find out the radio security code, if any, address to Section Replacement of the battery.

2. Using a plastic wedge, remove the cover over the speaker from the shelf, as described in Section Removal and installation of shelves.
3. Disconnect the speaker connector.
4. Open the trunk.

5. Press the locking tabs inward (1) speaker and remove the speaker from the chassis.

6. Remove the 4 screws and remove the speaker from the body.


Setting

PERFORMANCE ORDER

1. Installation is performed in reverse order of removal.
2. Attach a weight cable (-) battery when the ignition is switched off. Replace the cabin air filter box. If necessary, enter the code for the radio and set the time on the clock.





« previos page
Removal and installation of the radio
next page »
The digital CAN data bus

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.