add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Golf IV (1997 release)

general info. full specifications. diagnostics. hints. tips. tricks
Volkswagen Golf 4
Home
 
Volkswagen
Golf 4
Instructions
Engine
Cooling system
Fuel System
Exhaust system
Ventilation and heating system
Coupling
Transmission
Suspension brackets and power shafts
Steering
Wheels and tires
Brakes
Technical specifications
ABS / EBV / EDS / ASR / MSR
Replacing the front brake pads on support FS-III
Replacing brake pads on a support FN-3
Replacing the rear brake pads on disc brakes
Brake disk
Adjusting handbrake
Replacing the rear brake pads Drum brakes
Withdrawal
Setting
Removing and installing rear working brake cylinder
Bleeding the hydraulic brake system
Brake pipelines and hoses
Check the brake servo
Removal, installation and adjustment of brake light switch
Removal and installation of cables of a manual brake
Key brake failure
Body
Electrical equipment and wiring
 


Hit Counter by Digits


print page printable version

Replacing the rear brake pads Drum brakes



Rear brake drum

1 - sensor ABS;
2 - Allen screw 8 Nm;
3 - pin hub;
4 - a bolt, 60 Nm;
5 - Phillips screws;
6 - a brake drum;
7 - a protective cap. When removing the brake drum does not require the removal of the protective cap;
8 - Self-locking nut dvenadtsatigrannaya 175 Nm. When you install a new nut should be used;
9 - the hub of the rear wheel bearing;
10 - Brake shield with brake pads;
11 - rear beam

Rear brake drum brake pads front-wheel drive

1 - spring plate. To remove the spring you must click on the plate and turn
by 90 ?�;
2 - a spring;
3 - brake shoes with a lever drive
handbrake;
4 - the upper return spring;
5 - lower return spring;
6 - a spring;
7 - brake pads. The minimum thickness of the brake pad lining is 2.5 mm;
8 - cap. After removing the cap from
You can check the brake board
the state of the brake pads;
9 - roll pin;
10 - brake board;
11 - a bolt with hexagon socket, 8 Nm;
12 - wheel brake cylinder;
13 - wedge. When removing the brake drum wedge you want to move up;
14 - spacer bracket. When installing the spacer strips it is necessary to grease the G000650;
15 - pressure spring

The rear drum brake is an automatic adjustment of a backlash brake pads. Thus Spreader strap automatically changes its length and thereby providing a constant clearance between the brake drum and the brake shoes. To do this, between the front pad and expander strap wedge is placed with a spring, which is a continuation expander strap. After a single press on the brake pedal is installed the required clearance. If, due to increased wear of course pad, the wedge under the influence of spring and expander strap falls down. Thus, changing the length of the expander strap and automatically maintained a gap of brake pads.

PERFORMANCE ORDER

A warning

Be sure to make replacement of all blocks on the same axis even if deterioration borders were reached only one shoe.


1. The thickness of the rear brake linings drum brake can be checked without removing the brake drums. Remove the rubber cap, which is set at the entrance of a cable of a manual brake on a brake board.
2. Highlighting a portable lamp, check the thickness of the brake linings.
3. Lift the rear of the car and fix on supports.
4. Remove the rear wheel and release the parking brake.
5. Remove the screw that secures the brake drum.
6. Turn the brake drum so that one of the holes for the wheel bolts is angled 45 ?� from a vertical plane towards the front of the vehicle.
7. Release the brake pads, which insert a screwdriver through the hole and move up the wedge.
8. Remove the brake drum. If necessary, use a universal stripper.

A warning

When you remove a brake drum not press the brake pedal, as the pistons may come out of the working brake cylinder.


9. pliers press cup springs, rotate them by 90 ?� and remove together with springs. By turning the back side cheshek brake shield retaining pin in place.
10. Similarly remove the cup spring and the second brake pad.
11. Using a screwdriver, remove the brake pads from the bottom of the support.
12. Remove the lower return spring.
13. Disconnect from the lever of the brake pads Brake cable.
14. Remove the brake pads and secure them in a vise. Remove the upper return spring and the spring tension of the wedge.
15. Remove the pressure spring expander strap and remove the expander bar with a wedge (arrow indicates the place disconnection).




« previos page
Adjusting handbrake
next page »
Withdrawal

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.