REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Nissan Maxima QX (1993 release)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Nissan
	Maxima QX
		Introduction
		Operating Instructions
		Adjustment and routine maintenance
		Engine
		System of cooling, heating
		The power supply system and release
		Electric motor
			General information and precautions
			Starting the engine from the auxiliary power supply
			Check and replace batteries
			Check and replacement of wires of the battery
			Ignition System - general information and precautions
			Check the functioning of the ignition system
			Check and replace the ignition coils
			Check and replacement of the power transistor (models 1993 and 1994 issue.)
			Check, adjustment, removal and installation of the distributor of ignition (models 1993 and 1994 issue.)
			Check and adjust the ignition timing settings
			Charge system - the general information and precautions
			Checking the status of the charge
			Removing and installing the generator
			Start system - the general information and precautions
			Check of serviceability of functioning of a starter and start chain
			Removing and installing starter
			Replacement of the traction relay
		Engine Control Systems
		Transmission
		Coupling and power shafts
		Brakes
		Suspension and steering
		Body
		Onboard electric

printable version

Removing and installing the generator

The design of the generator (models 1993 and 1994 issue.)


1 - Pulley 2 - Front cover 3 - Rotor 4 - Rear Bearing 5 - The nut (39 ÷ 59 Nm) 6 - Front Bearing	7 - Bearing Holder 8 - The stator 10 - Brush Assembly 11 - Back cover 12 - coupling bolts (3.1 ÷ 3.9 Nm)

The design of the generator (model 1995 issue.)


1 - Pulley 2 - Front cover 3 - Front Bearing 4 - the bearing retainer 5 - Rotor 6 - contact ring 7 - Stator 8 - coupling bolts (3.1 ÷ 3.9 Nm)	9 - Installation Details contact 10 - Condenser 11 - Brush holders 12 - Regulator 13 - Diode Arrays 14 - Laying 15 - Back cover

Models 1993 and 1994 Vol.

PERFORMANCE ORDER

1. The generator design is shown in the illustration.
2. Disconnect the negative wire from the battery.
If installed on the car stereo is equipped with a security code before to disconnect the battery make sure that have a correct combination for audiosystem input in action!

3. Poddomkratte car and establish it on props. At a corresponding complete set remove protection crankcase.
4. Remove the drive belt (see chap. Adjustment and routine maintenance).
5. Disconnect the wiring from the generator and the discharge wire.
6. Turn out fixing bolts and separate the generator from the engine block.

7. Install in the reverse order.
8. Do not forget to conclude install the drive belt and connect the negative cable to the battery. Adjust the tension of the belt (see chap. Adjustment and routine maintenance).

Models from 1995 MY.

PERFORMANCE ORDER

Poddomkratte car and establish it on props. At a corresponding complete set remove protection crankcase and locker protect the arch of the right front wheel.
3. Remove the drive belt (see chap. Adjustment and routine maintenance).

4. Disconnect the alternator wiring and outlet wire.

5. Remove the cooling fan assembly from the casing (see chap. System of cooling, heating).
6. Remove the compressor K / V and, without disconnecting the hydraulic lines, slide it to the side.

7. Turn out fixing bolts and separate the generator from the engine block.

8. Install in the reverse order.
9. Do not forget to conclude install the drive belt and connect the negative cable to the battery. Adjust the tension of the belt (see chap. Adjustment and routine maintenance).

« previos page
Checking the status of the charge

next page »
Start system - the general information and precautions