 printable version
Control equipment
Control equipment 1 - tachometer;
2 - electronic watch with a digital display or trip computer display;
3 - coolant temperature;
| 4 --reserve fuel;
5 - Display selector position;
6 - speedometer;
7 - meter track with service indicator |
Location of control devices depend on the particular car model and engine type. Tachometer (1)
Tachometer needle in any case should not go into the red zone of the scale.
Starting time of the red zone on the scale is dependent on the particular engine.
The early switch to a higher gear saves fuel and reduces noise of the engine and transmission.
Switch to a lower gear should be as late as possible, shortly before the time when there will be jerks in the engine.
Electronic clock with digital display (2)
| To set the current time, you should use the button located on the right beneath the tachometer. |
Turn the key counter-clockwise (arrow 1) to set the stop watch. With a single button, turning a short-term rearrangement of one hour. When you turn the key and hold it in this position there is a continuous rearrangement of hours.
Turn the knob clockwise (arrow 2) until it stops set minutes. With a single button, turning a short-term rearrangement of one minute. When you turn the key and hold it in this position there is a continuous rearrangement of minutes.
With this button you can set the clock with the second accuracy: | PERFORMANCE ORDER | | 1. Rotate button to the right (arrow 2) until such time until the clock will show the time one minute less than the reference clock. | | 2. Use immediately turn to the right when the second hand control hours with the exact course will reach a full minute. |
|
Trip computer display (2) | The picture shows the display with trip computer display average specific fuel consumption. |
Trip computer display (multi-pointer MFA), along with an indication of the current time even gives a lot more information: - The temperature of outside air;
- Instantaneous fuel consumption;
- Average fuel consumption;
- Distance traveled;
- Average speed;
- Travel time. Icon shows the currently parameter appears, except this time, at the upper limit of the display field.
Alternate removal more information on the display when the ignition is carried out by briefly pressing the key balancer B, located on the handle of the windscreen wiper.
If you click on the top face of the key, the testimony of various sizes will be replaced one after another.
If you click on the bottom button, the testimony of various sizes will be replaced one by one in reverse order. STORAGE The onboard computer is equipped with two automatic drives.
The drive to store information for individual trips (MFA 1) accumulates in itself since power until the ignition is switched off following information about the trip: the movement, the distance traveled and the amount of fuel consumed.
On the basis of these data, calculate the average speed and average fuel consumption.
If within two hours after the ignition is switched off the car traffic was resumed, new data is added to the former and are included in the calculation of averages. At the break in driving lasting more than two hours, all the data in the drive will be deleted automatically.
The drive to store information on the total mileage (MFA 2) accumulates in the car all the data for any number of journeys until a totals value of 100 hours of driving 10,000 kilometers and 1,000 liters of fuel consumed. The accumulated data is used to calculate the results obtained for all trips Our average fuel consumption and speed.
When one of these limit values is exceeded, the data on the drive is erased and the total mileage countdown begins again. This drive, as opposed to the drive of the individual trip, do not erase the data after two hours of break in driving.
To request information should contact the appropriate drive by pressing the A key on the steering column switch wiper.
In the field of the clock with digital display appears the corresponding figure for the selected drive:
- MFA 1 - drive to store information on individual travel;
- MFA 2 - Drive to store information on the total mileage.
From drives, you can call the following indicators:
- The average fuel consumption;
- Distance traveled;
- Average speed;
- Driving.
The amount of fuel used is not shown. If you hold down the key more than two seconds And, the data in the selected drive will be erased.
When disconnecting the battery contained in both drives is erased. INDICATIONS
When the ignition is on or the display shows the last selected index or reading the outdoor temperature with a snowflake icon (warning the possibility of ice).
No icon | Current time | Display current time is saved when you turn off the ignition.
Setting the time it is done by turning the setting button beside the tachometer on the dashboard. | FROM | Outside air temperature | Reading range from 40 ?� C to + 58 ?� C. When the vehicle is stationary or moving at a very slow speed shown by the outdoor temperature may be somewhat higher than the true value because of the influence of the thermal radiation of the engine.
When the outside temperature is between + 4 ?� C to -7 ?� C in the display in addition to the value of the outside temperature is shown in the form of a snowflake icon (warning the possibility of ice).
This icon flashes for about 5 seconds and then lit until the outdoor temperature exceeds + 4 ?� C or falls below 7 ?� C.
When warning of icy pointer switches to the displayed indicator on the outside temperature reading (warning about the possibility of ice).
A warning  When you largest outdoor temperature to draw conclusions about the possibility of icing of the road, keep in mind that the ice on the road may occur at a temperature of about + 4 ?� C
Keystrokes on the steering column switch, you can switch back to the previous index display. | | Instantaneous fuel consumption | Showing fuel currently in liters per 100 kilometers.
The calculation of the instantaneous fuel consumption is made through the 30 meters run. The vehicle is stationary holds the last reading of the instantaneous fuel consumption.
If you start the engine selected indicator instantaneous fuel consumption, the first 30-40 meters of motion will be shown the value of average fuel consumption.
With instantaneous fuel consumption readings can adjust your style of driving according to the desired fuel consumption. | | Average fuel consumption | Lights average specific fuel consumption and the fuel consumption amount is not currently.
This indicator is displayed starts immediately after coating tridtsatimetrovoy distance from the point where data has been erased in the appropriate drive. Prior to that, instead of numbers on the display shows dashes. During the movement of the displayed figure is updated every five seconds.
When the selected drive to store information for individual trips (MFA 1) the display shows the average fuel consumption for this trip.
When storage for storing information on the total mileage (MFA 2) the display shows the average fuel consumption of all recent trips.
A warning The amount of fuel used is not shown.
| | Distance traveled | When the selected drive MFA 1 on the display running after ignition, or cleaning the drive.
When the selected drive MFA 2, the display shows the mileage on all individual journeys.
The maximum value that can be indicated is 9999 km. If the mileage exceeds this value, starting from zero. |  | Average speed | | Everything described for the 'average fuel consumption', valid for the indicator "average speed". | | Moving time | | Everything described for the 'distance traveled' true for the 'traveling time. " The maximum value of the reading is 99 hours and 59 minutes. When this value is exceeded, it starts again from zero. |
| The temperature of the coolant (3) |
| and - a low temperature zone. Avoid high engine speed and let the engine high load;
b - zone normal operating temperature. In normal driving the needle should be in the middle zone of the scale;
with - warning light |
The index works at the included ignition.
After turning on the ignition for a few seconds when checking the performance lit warning light (s). At high engine loads and high ambient temperatures from time to time possible entry arrow in the upper zone of the scale. This should not be a concern as long as the lamp glows alarm (s). If during movement warning light starts to burn, it is necessary first of all to see what temperature indicates coolant temperature.
If the needle is in the area of normal operating temperature, should be as soon as possible to add coolant to the cooling system.
If the needle is in the right area of the scale, this means that the coolant temperature is too high. It should stop the car, stop the engine and determine the cause of raising the temperature of the coolant.
A warning Extra lights front grille reduces the effectiveness of its action. At high ambient temperatures and high engine loads there is a risk of overheating the motor!
| Pointer stock of fuel (4) |
| The arrow indicates the zone of reserve fuel supply.
d - warning lamp
|
The index works at the included ignition.
The capacity of the fuel tank of the car is about 55 liters.
If the pointer has reached the reserve fuel supply zone (indicated by the arrow) and simultaneously warning lamp is lit (d), it means that there is still about 7 liters. The display position of the selector of an automatic transmission (5)
This shows the position in which there is a selector of an automatic transmission. Trip meter / counter of daily run (6)
The top counter indicates the total mileage of the car, the lower - run a certain point (the counter of daily run).
The last digit of the lower counter reading is 100-meter intervals.
Zeroing the bottom of the counter is made by pressing the speedometer. Service indicator (7)
When the time comes for regular maintenance, the lower counter (the counter of daily run) speedometer receive one of the following symbols of the desired type of maintenance:
- Oil change - service OEL or service OIL;
- Inspection service - service INSP.
Approximately one minute after the start of the engine disappears reading notation necessary maintenance. You can also include the reading of daily run by pressing and holding the button for more than 0.5 seconds setting button daily counter.
Service company Volkswagen, which makes the maintenance work after the service indicator is set to the original position.
If the service was not performed in the service enterprise a Volkswagen, service indicator should be set to the initial position in this order: | PERFORMANCE ORDER | | 1. With the ignition off, press and hold down the zeroing button under a speedometer. | | 2. Turn on the ignition and release the zeroing button only when the display shows one of the images required type of service. | | 3. The minute button to set the clock with digital display, turn right (at the clock to pull the arrow indication button). The display shows: "service-". | | 4. Turn off the ignition. Only now produced initial setting to indicate the need for maintenance. | | 5. In any case, you need to install only the required type of service. Otherwise, the time required service will be indicated incorrectly. Press the setting button, you can select a separate type of service. | | 6. Do not attempt zeroing in between two Maintenance - the device will give incorrect readings. |
|
When the battery disconnected mileage readings are stored after maintenance.
If after repair the speedometer replaced, you must re-program the service indicator. This operation must be carried out in the service enterprise a Volkswagen. If the service-indicator anew is not programmed, it is necessary to carry out maintenance work on a vehicle on the "Service Booklet", rather than the service indicator.
|
