add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Mazda 323 (1985 release)

general info. full specifications. diagnostics. hints. tips. tricks
Mazda 323
Home
 
Mazda
323
Introduction
Gasoline engines
Engine oil
Engine cooling system
Ignition system
The power supply system, the carburettor, fuel injection system
Diesel engine
Exhaust
Coupling
Manual gearbox
Automatic Transmission
Suspension and steering system
Brakes
Wheels and tires, a body, car coloring, care of the car
Electrical system
Troubleshooting the electrical system
Check the switch on the power transmission
Relay test
Check the wiper motor
Checking the direction indicators
Check stoplights
Check the rear window defogger
Disconnecting and connecting the connectors
Fuse
Replacing fuses
Removing and installing battery
Battery check
The battery discharges itself
Charging the battery
Storage Battery
Generator
Security measures for the alternator
Check the generator voltage
Removing and installing the generator
The components of the generator
Dismantling generator / replacing the carbon brushes
Removing and installing starter
Check / replacement of the traction relay of a starter
Heater, illumination system, devices
Controls and operation receptions
Electrical diagrams
 


Hit Counter by Digits


print page printable version

Removing and installing the generator



Gas engine

Withdrawal

PERFORMANCE ORDER

  1. Disconnect earth cable from the battery.

This data is erased from the memory of malfunctions of the engine or a protective code of a radio receiver. Before disconnecting the battery should read instructions in Section Removal and installation of the battery.


  1. Disable the multi-connector -2- behind the generator.
  1. Unscrew the main cable from the terminal B. -3-
  2. Remove the V-belt, see. Chapter Gasoline engines, Section Removal and installation / belt tension.
  3. Unscrew the screws on the bracket of the generator, as well as the tension bracket and remove the generator.

Setting

PERFORMANCE ORDER

  1. Paste generator and screw the bracket, without tightening completely.
  2. Insert the adjusting screw.
  3. Check the wear of the V-belt and replace if necessary.
  4. Apply and tighten the V-belt, see. Chapter Gasoline engines, Section Removal and installation / belt tension.
  5. Tighten the bolt with a force of 50 Nm, the tension bolts to 25 Nm.
  6. Connect the electrical wires to the generator.
  7. Connect the earth cable to the battery.
  8. If available, set the clock and set the security code radio.

Diesel engine

Withdrawal

PERFORMANCE ORDER

  1. Disconnect earth cable from the battery.

This data is erased from the memory of malfunctions of the engine or a protective code of a radio receiver. Before disconnecting the battery should read instructions in Section Removal and installation of the battery.

  1. Lift the front of the car, see. Chapter Introduction.
  1. Unscrew the front exhaust pipe.
  1. Disconnect vacuum hoses -2-, after loosening and sliding clamps.
  1. Disconnect the oil hoses -3-. Catch any escaping oil. Cover with a cloth surrounding parts.
  2. Disconnect the multi-connector -5- behind the generator.
  3. Unscrew the main cable from the terminal B. -4-
  4. Remove the V-belt -6-, see chap. Gasoline engines, Section Removal and installation / belt tension.
  5. Unscrew the bolts to the bracket of the generator, as well as the tension bracket and pull down -7- generator.

Setting

PERFORMANCE ORDER

  1. Paste generator and screw the bracket, without tightening completely.
  2. Insert the adjusting screw.
  3. Check the wear of the V-belt and replace if necessary.
  4. Apply and tighten the V-belt, see. Chapter Gasoline engines, Section Removal and installation / belt tension.
  5. Tighten the bolt with a force of 50 Nm, tension bolt c torque of 25 Nm.




« previos page
Check the generator voltage
next page »
The components of the generator

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.