 printable version
Care of an upholstery and carpets salon
Every three months remove rugs and mats and clean the interior panels upholstery. If necessary, this procedure may be performed more frequently. For garbage collection and cleaning of rugs and mats can use a stiff brush or broom. Furthermore, all surfaces should be thoroughly lesosit propyl, especially along seams, joints and folds of material.
Ingrained dirt can be removed from the carpet by means of domestic or special car shampoo, which for convenience are issued in the form of aerosols - follow the manufacturer's instructions. Finally, vacuum the treated area and "vzeroshte" pile with a stiff brush.
 | Do not leave within the interior upholstery to dry scrubbing, no electric heaters! |
Leather upholstery requires special care. Stain removal should be done with a very mild soap solution of warm water. The solution is applied with a soft cloth, then wipe the surface. In no case do not use for cleaning leather upholstery alcohols, gasoline, and other various kinds of solvents.
Try to avoid prolonged contact with leather upholstery to direct sunlight. Try to park the car in the shade, use sunscreen curtains, etc.
 | 1. In the absence of access to the rear side body panels for percussion dents, it must be pulled with a hammer with sliding brisk. In the deepest part of the dent, or along its border, or tamp nasverlite small holes at a distance of not less than 2.5 cm from each other ... |
 | 2. ... then screw the stem into the hole hammer and bring it into effect. Conventional tapping with a hammer on the edge of the dents to help the metal to take its original shape. After completing this procedure, the surface indentations must come close to its original contour and approximately 0.3 cm above the surface of the surrounding metal. |
 | 3. Use the coarse sandpaper to remove the paint down to the bare metal. You can do this manually, but the device is shown in the photo, it will help you speed up the process. With a thin, approximately number 320 sandpaper negated paint in a radius of at least 2.5 cm around the site dents. |
 | 4. After removing the paint is better to check by feel than by sight, enough is smooth metal surface. Zastuchite hammer convexity and / or pull the cavity where it is needed. Clean repair surface wax or silicone stain remover. |
 | 5. Follow the instructions on the package, mix the pack of plastic filler and hardener. Mixing is critical, and if you break it, plaster hardens too slowly or too quickly (and you do not have time to apply it and give the necessary form). |
 | 6. Working quickly so as not to harden plaster, using a plastic applicator to apply pressure to the surface of the metal, making sure there is a full engagement with the metal. Deal with putty that it took shape similar to the original form of the site and slightly above the surrounding surface. |
 | 7. Allow the putty to harden to the point that it could only push your fingernail. Use the file or device, shown in the photo, roughly processed putty. |
 | 8. Using a rough sand paper attached to a board or bar, treat plaster so that it becomes smooth and even. Gradually move on to more and more subtle varieties of paper, always use a plate or a bar, and finish processing the number 360 or 400. |
 | 9. The processing of hand should not feel the blend of fillers to the bare metal and from bare metal to old paint. If this goal is achieved, remove dust and cover the adjacent panels and trim parts. |
 | 10. Apply several coats onto the surface. Do not spray too much primer, so it does not drip down, and after application of each layer, let the previous dry. Usually it uses a professional spray gun, but in auto parts stores is commercially available in an inexpensive primer aerosol. |
 | 11. The primer will help identify defects or scratches. Fill them with a polishing paste. Follow the instructions on the package, treat it with a thin (?�� 360 and 400) sandpaper until smooth. Repeat polishing, causing polishing paste and polishing it, as long as the primed surface is completely smooth. |
 | 12. Finish sanding very thin paper (?�� 400 and 600) to remove excess primer. Wash the area with water treatment and let it dry. Use sticky cloth to remove any dust, then apply a coat of outdoor paint. Do not try to wipe or wax coating applied to the land as long as the paint is completely dry (at least two weeks). |
|
