add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Nissan Terrano II (from 1985 to 1999 model year)

general info. full specifications. diagnostics. hints. tips. tricks
Nissan Terrano 2
Home
 
Nissan
Terrano 2
Operation and Maintenance
Maintenance Vehicle
Introduction
Terms of service
The procedure for making adjustments -General comments
Check liquid level
Checking the liquid level in the automatic transmission
Checking the power steering fluid
Checking tire (every 400 kilometers or weekly)
Battery Care
Care of cooling system
Check wiper blades
Checking the condition of the hoses located in the engine compartment.
Checking and adjusting the brake pedal
Changing the oil and oil filter
Check and adjustment of backlashes of valves
Grease the chassis and steering
Check suspension and steering
Check the propeller shaft
Exhaust system check
Check and adjust the clutch pedal
Checking the oil in a manual transmission
Checking the oil level in the transfer case
Checking the oil level and karteredifferentsiala (or rear axle)
Shift of wheels
Check the brakes
Check the fuel system
Check the thermostat of the air filter
Drive belts - Check, adjustment and replacement
Checking of safety belts
Replacing the air filter and PCV
Replacement of the fuel filter
Replacement filter ejection valve final oxidation of the exhaust gases
Changing the filter tank with an absorber
Check the throttle body mounting
Check and adjustment of turns of idling (engine with fuel injection)
Changing the oil in the transfer case
Oil replacement in a manual transmission
Changing the oil in the gearbox rear (or front) of the bridge
Transmission Fluid Replacement! in automatic transmission
Changing grease in the front wheel hub and check bearing (only for rear-wheel drive cars)
Substitution coolant
Check and replacement of the valve crankcase breather
Replacing spark plugs
High-voltage wires Checking and replacing
Distributor cap and rotor slider - checking and replacement.
Check and installation of the moment of ignition.
The oxygen sensor
The four-cylinder engine
Engines VS
All engines
Systems of cooling, heating, ventilation and air conditioning
Fuel and an exhaust system
The system of electric motor
Emission of exhaust gases
Manual transmission
Automatic Transmission
Coupling the propeller shaft and rear axle
Chassis car with wheel formula 4x4
Brakes
Suspension and steering
Body and trims
Electrical system
 


Hit Counter by Digits


print page printable version

Grease the chassis and steering



1. Accessories for lubrication are shown in the photo. 15.1 Accessories for greasing
2. To lubricate the chassis and steering applies universal lithium greases grease for ball bearings to be the front suspension arms, steering drafts tips, front and rear driveline (on the car with wheel formula 4x4).
3. Place the top bearing lubrication is at the top of the housing support (photos), lubrication is necessary to remove the wheel. Access to the nipple of the lower support is provided through the hole in the lever (photo). Greasing hole tie-rods, remove the cap (see photo). In the driveline lubricated hinges and sliding splined connection (see photo).
4. Lift the car and establish on supports.
5. Remove the plug and screw lubricator (to the vehicle).
6. Squeeze a little grease from the syringe and wipe clean.

15.3a threaded hole for the oil can to lubricate the upper bearing cap plugged
15.3a threaded hole for the oil can to lubricate the upper bearing cap plugged


15.3v oiler plug holes in the tip rod
15.3v oiler plug holes in the tip rod


7. Coat the syringe all the connections. Ball joints of the syringe until the grease fill rubber boots (felt by pressing). If the grease-vyho children with an oil, the oil can tighten or loosen the valve and check the purity of the oil can.
8. Remove any residual grease.
15.3g plug holes in the universal joint lubricator
15.3g plug holes in the universal joint lubricator


15.3b hole in the lever for the lubrication of the lower support (on a / m earlier releases)
15.3b hole in the lever for the lubrication of the lower support (on a / m earlier releases)


15.Zg Oiler spline
15.Zg Oiler spline


9. Lubricate the cable and handbrake lever.
10. Lower the car.
11. Lubricate the friction parts hood locks and rear doors, lubricate the end of the rope.
12. Lubricate door hinges with a few drops of oil to the engine.
13. The cylindrical door lock switch lubricated aerosol graphite lubricant.




« previos page
Check and adjustment of backlashes of valves
next page »
Check suspension and steering

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.