REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Kia Clarus (1995 issue)

general info. full specifications. diagnostics. hints. tips. tricks

Home

Kia
	Clarus
		Maintenance
		Engines FE DOHC and DOHC T8
		Greasing system
		Cooling
		The power supply system and release
		Fuel system
		Ignition system
		Coupling
		Manual transmission
		ACP G4A-EL
			Technical data
			Search and definition of malfunctions
			The table of fast diagnostics
			Self-diagnostic system
			Fault codes
			Diagnostic connector
			Cleanup operation
			Testing of teamwork of an automatic transmission and the engine for the motionless car
			Testing time lag
			Testing of pressure transmission fluid
			Testing for the pressure reduced by the valve
			Check of level and a liquid condition in an automatic transmission
			Leaks of a liquid from an automatic transmission
			The accelerator cable
			Mode Switch
			Brake light switch
			The temperature sensor Transmission Fluid ATF
			Check the resistance of the pulse generator
			Solenoid valves
			Removal of an automatic transmission
			The general recommendations about transmission dismantling
			Dismantling of an automatic transmission
			Check and adjustment of preliminary loading of bearings
			Assembling automatic transmission
			Installation of an automatic transmission
			Oil radiator
			Disk Drive
			Check of work and adjustment of position of the selector lever
			Lever
			Repair of the selector lever
		AKP 50-40 LE
		Axes and power shafts
		Steering
		Wheels and tires
		Suspension
		Body
		The air conditioning system
		Electrical equipment
		Brakes
		Electric schemes

printable version

Repair of the selector lever

Lever

1 - a socket;
2 - screws;
3 - head of the selector lever;
4 - a casing;
5 - Display Panel;
6 - position indicator lamp;
7 - cam;
8 - the roller clamp assembly;
9 - auxiliary plate;

10 - elastic plate, top;
11 - elastic plate;
12 - pin;
13 - Roller latch;
14 - axis;
15 - a nut;
16 - the selector lever;
17 - guide plate;
18 - an arm of the selector lever.

Dismantling, check and assemblage

PERFORMANCE ORDER

1. Disassemble the selector lever in the sequence shown in the figure.
2. Insert a thin piece of metal from the connector contacts and squeeze down the pin for fixing them.
	3. Pull the pin from the connector.
4. Check the details and, if necessary, repair or replace them.
5. The assembly is carried out in sequence, return dismantling.
6. Apply grease to the inside of the clamp and install it on the elastic plate.
7. Move the selector lever to R.
	8. Set the free state elastic plate, a top plate and a resilient supporting plate.
	9. Adjust the gap between the guide plate and the guide pin and tighten the screws. Tightening torque: 2.0-2.9 N ??? m
10. Establish in a free state on the cam follower.
A warning Clearance is reduced by turning the cam clockwise.
11. Adjust the gap between the guide plate and the guide pin by turning the cam.
	12. Establish a head of the selector lever and make sure the gap is the specified value.
13. Otherwise, the assembly again from step 2.
14. Remove a head selector lever
	15. Apply grease to the cam, as shown in Fig.
16. Move the selector lever to R.
	17. Align the screw holes in the slider in the display panel. Install the thick wire to support the slider.
18. Temporarily install the display panel bracket to the selector lever.
	19. Tighten the screws of the display panel in the order shown in the figure. Tightening torque: 2.0-2.9 N ??? m
20. Remove the wire.
21. Make sure that the selector lever position corresponds to the display panel in each position.

« previos page
Lever

next page »
AKP 50-40 LE