 printable version
Preparation for painting
| - Before painting the car wash to avoid inclusions of dirt.
- Operate only at temperatures above 12 degrees, but not in direct sunlight or in strong winds.
|
|
Removing rust | - Tape off the repair circuit protective tape (tezakrepp) to not inadvertently damage the surrounding paintwork.
- Remove all visible and hidden under the rust bubbles triangular file or screwdriver, and coarse sandpaper with grain 120.
- Feather edges around the damaged area with stops at 1-2 cm on the intact surface of sandpaper with grain 320.
- Galvanized body parts should be cleaned only as far as possible to the ground, not to the zinc coating.
|
|
The application of anti-corrosion primer ("Primer") | - Place repairs cleaned of dust and grease nitrosolvent and a clean cloth and allow to dry.
- To prevent problems of incompatibility, "Primer" must be of the same manufacturer as the applied paint. Otherwise, the paint will bubble and wrinkle.
- Spray the "Primer" om a distance of about 25 cm is very narrow, but covering the surface of a stream. To avoid falling into an aerosol mist of the surrounding surface, cover them with protective tape and newsprint.
- After 10-15 minutes ventilation can be repeated spraying. If you spot repair putty should be applied before "Primer" is to dry thoroughly.
|
|
Spackling 2 different kinds of fillings: a two-component filler and fine putty. Two-component filler mixed prior to treatment and hardener. It hardens quickly and requires a quick application. It is used to align the large irregularities metal. The thin coating is viscous, which are aligned small surface. It can be applied in several layers. Both types of fillings are available in tubes and jars, and a thin coating is an aerosol.  | Although banks often written recommendation putty filler is applied direct to metal, in any case, suitable preparation anticorrosion "Primer" om. |
| - Apply to Align or sealed with fiberglass seat and two-component putty to harden. Follow the manufacturer's recommendations.
- After solidification irregularities clean manually or vibroshlifovatelem. This use sanding paper with a grain of "180". Now it is possible to apply and waterproof abrasive paper. In this case, the place of repair from time to time plentifully moisten with water (sponge).
- Finally, wipe repair area and allow to dry.
 | - With wide elastic plastic blade applied to the repair area thin layer of putty and give it to harden for at least 2 hours. In large rounded contours and recommended application of the aerosol filler.
|
- Depending on the thickness of the applied coating layer should be thin to dry out for 2 to 3 hours.
|
|
Are smoothed | - Sanding is a different grain sizes. The smaller the number, the coarser the paper. For grinding a two fillings recommended grains from 180 to 240; Fill putty and stripped the old paint with water grain 360. For the last stage of grinding water is recommended sanding paper grain 600.
 | - Putty place to grind paper grain 360, while constantly keeping on the spot repair sponge. From time to time to immerse the sponge in clean water.
|
- For wet fine grinding followed by best fit special waterproof paper finishing with grain 600, with zashlifovyvayut and the surrounding surface. Thus polish only in the direction of the longitudinal dimension of the car; while remaining small scratches from grinding inking less noticeable.
|
|
Cleaning | - Before covering the ground surface paint, as well as the surface around her two palms in width should be freed from traces of grease and silicone. It is best for this suitable silicone remover.
- After grinding thoroughly clean the repair area and all around the vehicle accurately pasted newsprint and pecking tape. When painting wings also protect the wheels and shock absorbers.
 | - Try to paste the place of repair so that the painted surface is always limited to the closest molding or the edge of the body, as on the edge of the pasting occurs mound of paint, if the gradual transition of color to the original color is invisible, pasted at a distance from the place of repair in the width of two hands .
|
- To moisten the floor dust.
|
|
|
