add to favorites contacts sitemap
REPAIR MAINTENANCE OPERATION OF MOTOR VEHICLES
Volkswagen Golf IV (1997 release)

general info. full specifications. diagnostics. hints. tips. tricks
Volkswagen Golf 4
Home
 
Volkswagen
Golf 4
Instructions
Engine
Cooling system
Fuel System
Exhaust system
Ventilation and heating system
Coupling
Transmission
Suspension brackets and power shafts
Steering
Wheels and tires
Brakes
Body
Care body
Care of an upholstery and rugs
Repair of insignificant damages of a body
Repair of strong damages of a body
The front body panel
Removing and installing front bumper
Removing and installing rear bumper
Removal and installation of a forward wing
Removal and installation of facing of a niche of a forward wing
Removal and installation of facing of a niche of the rear wing
Hood
Hood lock
Removing and installing radiator grille
Removal and installation of a lateral overlay of a body
Door
Removal and installation of the rack rear door
Adjusting trunk lid / tailgate.
Removal and installation of the lock of a back door
Removal and installation of doors
Removing and installing interior door trim
Removing and installing interior door lock knob
Removal and installation of glass doors
Removal and installation of the door bracket
Removal and installation of the external handle of the door opening
Removal and installation of the lock cylinder housing
Removing and installing door lock
Central locking system
Removing and installing rear door upper trim
Removing and installing bottom trim back door
Luke
Purification gutter
Mirrors
The center console
Removal and installation of the top furnish in space for feet of the driver
Removal and installation of the glove compartment
Removal and installation of a lateral covering of space for feet
Removal and installation of overlays of thresholds
Removal and installation of the bottom facing of the central rack
Removal and installation of the right lateral covering of a luggage space
Removing and installing luggage compartment floor coverings
Removal and installation of back furnish of a luggage space
Removing and installing front seat
Side airbags
Removing the rear bench seat cushion
Removing and installing rear seat backrest
Washers and wipers
Electrical equipment and wiring
 


Hit Counter by Digits


print page printable version

Removing and installing interior door trim



This section describes the removal of interior trim driver's door. Interior finish rear door removed in the same way as the front.

Withdrawal

PERFORMANCE ORDER
1. Turn off the ignition and remove a wire of weight from the accumulator.
2. Insert a small screwdriver blade between the handle grip (1) and the recessed handle (2) and move the handle to the door trim. Use a screwdriver with a very thin blade, in order not to damage the plastic trim handles and door handle.
3. Using a screwdriver inserted under the edge of the recessed handle, remove the handle from the recess of the inside door trim. Do not remove the internal handle (2) door for a recess, as it is under the bridge (1) of the inner door trim (3 - an electric socket).
4. Pull the locking electrical connector from the connector and disconnect the electrical connector from the inside door handle.
5. Remove the 7 screws (arrows) securing the inner door trim (1).
6. Using a special device 799/4 (A) or self-made tool in the form of a flat fork, separate the door trim (1) from the door.
7. Lift the door trim upwards to release the upper part of the door trim of the window opening.
8. By moving back the rod (1) open the door, remove it from the guide (3) and remove the handle from the inside door opening (2 - screwdriver, 4 - thrust hook).
9. Disconnect the electrical connectors.
10. Remove the lower door trim inner seal glass (1) and insert it into the window opening.

Differences at removal of an upholstery right front door

PERFORMANCE ORDER
1. Insert the blade of a screwdriver (2) into the holes on the underside of the inside of the handle (3), and open the door by turning a screwdriver, remove the cover handle (1). In order not to damage the door trim, beneath the screwdriver blade plastic spacer.
2. Unscrew the 6 screws (indicated by arrows) securing the inner door trim.
3. The internal handle of opening of the door is attached to the door trim with two screws on the back of the upholstery. Loosen the inside handle of the door opening trim is possible only after removal of the door trim.

Setting

PERFORMANCE ORDER
1. Before installing the door trim, check the condition of clamps upholstery and, if necessary, replace damaged clips.
2. Install the clamps in the holes in the door trim.
3. Installation is made in sequence, return to removal.




« previos page
Removal and installation of doors
next page »
Removing and installing interior door lock knob

Copyright © 2010 AutoManuals.biz. Trademarks belong to their respective owners. All rights reserved.